HR2661 Makita Hammer - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This is a genuine manufacturer sourced replacement part designed for use with Makita power tools. It is a standard hardware which has multiple applications based on your tool. Please refer to diagram to ensure correct application. This pan-head screw is made out of metal and it is sold individually. Requires a phillips screwdriver to install or remove this screw.

This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes...Read more can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This replacement pin is an authentic OEM component which is made for use with Makita equipment. The pin is generally utilized to secure a part while allowing it to rotate freely. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams of your model for the exact location and the corre...Read morect installation of this pin. One durable metal item is included. You may need a screwdriver to take the unit apart when replacing this pin.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine manufacturer-sourced replacement field which is specially designed for Makita rotary hammers. A field is a central component of an electric motor which drives the tool, in conjunction with an armature it rotates the main shaft. Usually, a field is damaged by overloading the power tool, or because of a bad armature. It is...Read more highly recommended to replace both carbon brushes when replacing a field. Please note, this high-quality component is sold individually.

Genuine manufacturer approved replacement switch used on Makita rotary hammers. It is the part of the tool handling on/off operations. Since switches have moving mechanical parts, they will eventually wear out and will require a replacement. Switch has a plastic body and it is sold individually. To replace this switch you would need a sc...Read morerewdriver. • Remove screws used to hold two pieces of housing set together • Disconnect wires from the old switch and remove it from the housing • Place the new switch in the housing and connect wires to it • Reassemble the housing

This O-ring seal helps maintain proper internal pressure within rotary and demolition hammer mechanisms, supporting efficient operation and preventing leaks of air, oil, or grease. Made from durable elastomer material and measuring approximately 0.63 × 0.63 × 0.63 inches, it is designed to withstand heat and high-pressure conditions durin...Read moreg heavy use. Replacing a worn or damaged O-ring helps restore compression, improve hammering performance, and ensure smooth, reliable tool operation.