HR2450X3 Makita Hammer - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

It is an authentic Makita item that is designed for use with rotary hammers. A guide washer is a special part which helps to provide a tight fit between connected components. This part provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. It is a standard hardware which may have multiple a...Read morepplications. Make sure to check the appropriate diagrams for your specific model for the exact location and the correct application of this guide washer. Note, it is made of durable metal and is sold individually.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes...Read more can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This replacement tapping screw is an authentic item that is supplied by the original manufacturer for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this part. This high-quality phillips pan-head screw is made of durable metal and it is sold individually.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This cord protector is an OEM part designed for a variety of Makita power tools. It is attached where the power cord meets the tool. This part protects the cord from damage due to pulling, bending, or other strain. This rubber cord protector is sold individually. It does not include a replacement cord.

Genuine manufacturer approved replacement switch used on Makita rotary hammers. It is the part of the tool handling on/off operations. Since switches have moving mechanical parts, they will eventually wear out and will require a replacement. Switch has a plastic body and it is sold individually. To replace this switch you would need a sc...Read morerewdriver. • Remove screws used to hold two pieces of housing set together • Disconnect wires from the old switch and remove it from the housing • Place the new switch in the housing and connect wires to it • Reassemble the housing

This O-ring seal helps maintain proper internal pressure within rotary and demolition hammer mechanisms, supporting efficient operation and preventing leaks of air, oil, or grease. Made from durable elastomer material and measuring approximately 0.63 × 0.63 × 0.63 inches, it is designed to withstand heat and high-pressure conditions durin...Read moreg heavy use. Replacing a worn or damaged O-ring helps restore compression, improve hammering performance, and ensure smooth, reliable tool operation.

This replacement o-ring is supplied directly from the original equipment manufacturer, it is specially designed for use with Makita power tools. It helps to provide an air-tight seal between connected pieces, please make sure to check appropriate diagrams of your model for the correct location and application of this hardware. It is made ...Read moreof high-quality rubber and is sold individually, over time the material may wear out and begin to crack eventually requiring a replacement.