HLTD500AGW Haier Dryer - Overview

Sections of the HLTD500AGW

[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
DRYER BELT – Part Number: WE12X27366
DRYER BELT
★★★★★
★★★★★
(6)
PartSelect #: PS12342957
Manufacturer #: WE12X27366
$37.97
  In Stock
DRYER DOOR SWITCH – Part Number: WE10X27374
DRYER DOOR SWITCH
PartSelect #: PS12342942
Manufacturer #: WE10X27374
$22.78
  In Stock
DRYER DOOR LATCH – Part Number: WE10X27377
DRYER DOOR LATCH
★★★★★
★★★★★
(1)
PartSelect #: PS12342943
Manufacturer #: WE10X27377
$13.59
  In Stock
DRYER THERMOSTAT – Part Number: WE04X27365
DRYER THERMOSTAT
PartSelect #: PS12342924
Manufacturer #: WE04X27365
$45.86
  In Stock
IMPELLER – Part Number: WD-3768-01
IMPELLER
PartSelect #: PS4127882
Manufacturer #: WD-3768-01
  No Longer Available
DRYER DOOR LOCK MOTOR & SWITCH ASSEMBLY – Part Number: WE10X27373
DRYER DOOR LOCK MOTOR & SWITCH ASSEMBLY
★★★★★
★★★★★
(1)
PartSelect #: PS12342941
Manufacturer #: WE10X27373
$18.01
  In Stock
FILTER - LINT – Part Number: WD-2800-38
FILTER - LINT
PartSelect #: PS4127330
Manufacturer #: WD-2800-38
  No Longer Available
HINGE - LEFT – Part Number: WD-3450-12
HINGE - LEFT
PartSelect #: PS4127707
Manufacturer #: WD-3450-12
  No Longer Available
DRYER THERMOSTAT – Part Number: WE04X27367
DRYER THERMOSTAT
PartSelect #: PS12342925
Manufacturer #: WE04X27367
$18.33
  Special Order
HINGE - RIGHT – Part Number: WD-3450-13
HINGE - RIGHT
PartSelect #: PS4127708
Manufacturer #: WD-3450-13
  No Longer Available
SUPPORT A – Part Number: WE01X27974
SUPPORT A
PartSelect #: PS12577535
Manufacturer #: WE01X27974
$8.06
  In Stock
IGNITOR – Part Number: WE01X28027
IGNITOR
PartSelect #: PS12577536
Manufacturer #: WE01X28027
$89.20
  In Stock

Questions And Answers for HLTD500AGW

Be the first to ask our experts a question about this model!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
unit would not run at all but would turn on
They sent the wrong part even though I gave the unit model number and part number of the part.I described the part and gave the name used by the manufacture on the schematic from the back of the unit. The second person I spoke with to reorder the correct part took more time in understanding that a temp limiter is not the same as a temp sensor. The part is located on the inside back wall of the dryer behind the drum. It all had to come apart to get to it but was very easy even without the service manual.Unplug the unit. Remove the 4 screws on the back that lock down the top and pop off the top prying against the spring clips, move it out of the way but remember that its still connected by wires on the inside of the back. disconnect the 2 wires going to the door switch. Remove the two screws holding the front panel on located on the top. Pull up on the panel lifting it off of the spade brackets. Reach in down below and remove the belt from the pulley and drum. Pull up on the drum about 1" and the drum will be free. remove the drum. In the upper right hand corner is where you will see the temp limiter. Remove the 2 screws and unplug the wires. Assembly is the reverse order except to install the belt remove the access panel on the lower left corner of the back of the unit to gain access to the belt for installation....
Parts Used:
DRYER THERMOSTAT
  • Stanley from Cooper City, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!