HDR500B (1995) Husqvarna Tiller - Overview

This clevis pin is an OEM replacement part that is compatible with various makes and models of tiller and is sold as an individual part. The purpose of this pin is to snap or break under a certain amount of pressure if your tiller is jammed, to protect the more valuable components of your tiller. Measuring at approximately 2-inches long a...Read morend made of high-quality metal, replacing this pin should only require pliers to swap out the old pin for the new.

This is an authentic OEM sourced replacement component which is specially produced for use with Craftsman tillers. It is the main chain that helps to drive the unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Over time the chain may wear out and stretch event...Read moreually requiring a replacement to ensure peak performance. Keep in mind this high-quality metal part is sold individually.

Measuring approximately 1-inch in length, this handle lock is designed for use with various models of tiller machines. This handle lock is fastened to the base of the handle to secure the lock lever and is a genuine OEM metal part. This part is sold individually, so depending on your model, you may need 2 of them. Be sure to check your user manual or any diagrams for confirmation.

This is an authentic manufacturer sourced replacement part that is specially designed for use with gas powered lawn and garden equipment. The purpose of this gasket is to provide an air-tight seal for the gearcase. Over time gaskets tend to get compressed and deteriorate eventually requiring replacement. Please note one durable composite material gasket is included per order.

This needle bearing is sourced from the original equipment manufacturer for use in lawn and garden equipment. It is a cylindrical roller that allows the rotating parts such as the drive shaft to move smoothly and avoid friction damage. The bearing is made from steel and designed to withstand heavy loads, and harsh outdoor conditions. Over...Read more time the bearing may wear down from lack of lubrication, or damage from the heavy loads and impacts. If the needle bearing is faulty, you will notice excessive vibration, grinding and squeaking noises, and overall lower performance from your equipment. Carefully remove the old bearing from your equipment using bearing pullers and clean the area thoroughly to ensure a good fit for the new bearing. Lubricate the new bearing and press it into position to complete your repair.

This is an original replacement part manufactured for use with garden tillers. This bearing is commonly used to reduce friction between the ground shaft assembly and the right-hand side gearcase. The special bearing is available as an individual replacement part, please see model diagram for associative parts.

t is an authentic replacement bearing that is supplied by the original equipment manufacturer for use with garden tillers. Needle bearings are used to reduce friction between rotating parts. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the roller reduces friction. Symptoms of a faili...Read moreng bearing may include squealing, screeching, and an entirely new type of grinding noise. This high-quality component is made of durable metal and is sold as an individual part. Make sure to refer to the appropriate diagrams for your model to ensure the proper replacement procedure.

This is a genuine manufacturer-sourced replacement component which is specially designed for use with lawn and garden equipment. It is one of the parts that helps to provide a tight seal for the shaft, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind t...Read morehis durable item is made of high-quality metal with rubber and is sold individually.

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

This is a genuine Husqvarna part for use with Tillers. The tine digs into the ground to till the soil. The most common reason for replacing the tine is if it is worn. This part is sold individually and there are no tools needed to replace this part.

This is a genuine replacement part sourced from the original manufacturer for use with outdoor power equipment. The special needle bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This needle bearing is available as an individual replacement part.

This shift fork spring is found in your outdoor power tools. It helps you to control the speed and power of your machine by engaging and disengaging the gears in the gearbox. When the spring is broken, your machine will make grinding noises or jerk when you try to shift gears. If you overlook a damaged spring, it may lead to severe damage...Read more to the gear mechanism, which can result in costly repairs later. To remove the spring, start by turning off your machine and disconnecting the spark plug. Once you have access to the gearbox, locate the spring. It Is usually connected to the shift fork mechanism, but since the location can vary depending on the model and make of your machine, you will need to consult your user manual. Use pliers or a screwdriver to gently release tension on the spring. This may involve carefully compressing it or unhooking it from specific attachment points. Please be aware that this OEM metal spring is sold individually and is not included with the shift fork.