This lower rack wheel kit includes 8 wheels and 8 axles that allow the lower dishwasher rack to slide in and out smoothly. If your dishwasher door will not close, is noisy when operating, or the dishes are not cleaning properly, you might need to replace one or more of the wheels. Each wheel and axle are made of plastic, and fit into one ...Read moreanother so they can be clipped on to the lower dishwasher rack. Many of our customers found this repair to be quick and easy, and the only tool you should need to complete the repair is a pair of pliers.
This upper dishrack assembly is a genuine OEM replacement part designed for select dishwashers. It securely holds dishes, cups, and other items during the wash cycle, helping to optimize cleaning performance and maximize space. The assembly typically includes the rack itself along with the wheels that allow it to slide smoothly in and out...Read more of the dishwasher. Replacement may be necessary if the original rack is damaged, misaligned, or no longer holds items properly. To ensure a correct fit, it is recommended to verify compatibility with your specific model before installation.
This is a pump and motor kit for your dishwasher. This assembly replaces many old-style pump and motor kits that were manufactured since 1970. The instructions are included with this kit in to assist you. Take note that this is a completely redesigned kit by the manufacturer and now includes the drain solenoid. You may need to replace thi...Read mores part is if your appliance is leaking, not draining properly, noisy, or will not start or clean your dishes properly.
This genuine OEM dishwasher door seal gasket prevents water from leaking out of the dishwasher. If your washer is leaking from the door, check for wear on the gasket, and to ensure it is properly fitted. A hardened gasket can also make the door difficult to close. If the gasket is faulty, the part should be replaced right away.
The impeller and seal kit is used in a dishwasher. The kit includes all the parts needed to do this repair, including the impeller, seal, blade, filter, skidder and skidder holder. If your washer is leaking, not cleaning dishes properly, or not draining, then replacing some parts in the pump can help solve the issues mentioned. The tools ...Read moreneeded for this installation project are: 5/16 nut driver, 1/4 inch nut driver, flat-blade screwdriver, Phillips screwdriver, and pliers. Refer to the manual provided by the manufacturer for installation instructions and accurate guidance. Remember to unplug your dishwasher from the power source and wear work gloves as a safety precaution.
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in diameter while the larger one is 2 inches in diameter. The hose clamps secure the end of the water hose in place to prevent the hose from le...Read moreaking. If you notice leaking from the hose of your appliance, you may need to replace this kit. Protect your hands with work gloves during this repair to avoid injury.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower rack wheel was melted
523 of 550 peoplefound this instruction helpful.
Mark from Huntingdon Valley, PA
Really Easy
Less than 15 mins
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Was this helpful?
Thank you for voting!
The rear wheels were missing on the lower rack.
475 of 489 peoplefound this instruction helpful.
Teresa from Phenix City, AL
Really Easy
Less than 15 mins
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
Was this helpful?
Thank you for voting!
D/W would not drain. Water standing in bottom.
65 of 71 peoplefound this instruction helpful.
Ed from Cornelius, NC
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.
After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 scre
... Read morews, and plugging in the wire harness.
I work on a 260 + unit property, as well as working for a property management company who rents single family homes.
PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.