Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
HA3000W (POST.C348C774) Magic Chef Washer - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This V-style cogged tooth pump belt is used in conjunction with the drive belt in your washing machine. This belt is all black in color and is made entirely of rubber. It is twenty-two and a half inch...
The metallic pulley attached to this pump. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
This two speed motor performs 1725 revolutions per minute in one speed, and 1140 revolutions per minute in the second speed. It runs at 1/2 horsepower and carries 115 volts. You can use this washer mo...
VERY EASY!!! SAFETY FIRST-Always unplug the appliance. Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, r
... Read moreemove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
This was my fist time attempting to fix a washer. I had to guess on the length of the belt since the model number on the machine had worn off and the belt had snapped in a way that made determining the length difficult. At first, I ordered a belt that was too small. I realized this after I was unable to remount the motor stand onto the bo
... Read morettom of the machine. This model had the motor assembly right in front of the unit. It was easily accessed after removing the panel on the front of the machine. It was easy to remove the 4 screws (they were all visible) on the motor stand. After that I was able to disconnect the pump belt. This machine has seperate belts for agitation and the pump. The pump belt must be removed in order to install the agitator belt because they both are driven by the same shaft and the pump belt is positioned on the bottom. There is also a tension wheel for the agitator belt which might be easily overlooked. Make sure to install the agitator belt so that the tension wheel is on the outside of the belt's path. The whole job is fairly easy if you have the right part to begin with. If you have to force the belt onto the wheels, then you probably have a belt that is too small.
The only real problem was one spring loaded hose clamp to the rear of the pump. If it had been a standard clamp like the others I would have cut the repair time down by 2/3rd's. I did find that by removing one of the long wash drum springs, I then had more room to get my channellocks back there to get the stupid clamp to compress, and the
... Read moren used a screw driver to push the clamp back off the the connecting port. I replaced the camp w/ a standard clamp and the reassembly went quick and easy. Note, If you replace the pump drive belt with a new one, you WILL have to adjust the belt tension after a few minutes use.
