GXV620U1TAE2 Honda Engine - Overview

This is a Genuine OEM Fuel Pump Replacement. It has a Plastic Body. A Fuel pump is used when the Fuel tank is mounted lower than the Carburetor and cannot rely on gravity to carry Fuel through the Fuel line. It is recommended to check for hairline cracks and other damage to the external surfaces of the pump. If it is damaged discard the pump and perform a fuel pump replacement.

This gasket is a genuine OEM replacement part designed to seal the area between the exhaust pipe and cylinder head. It has a length of 3 inches and a width of 1.5 inches. The gasket prevents exhaust gases produced during combustion from escaping through the connection points and prevents air from entering the exhaust system. A faulty gask...Read moreet will result in increased emission of harmful gases, overheating, increased noise, and overall lower engine performance. You will likely need to remove the exhaust pipe to access the gasket. Once the gasket is removed, clean the surface to ensure a good seal and place the new gasket in position. Reconnect the pipe and ensure all parts are secure.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

A genuine OEM sourced replacement part that is specially produced for Honda egnines. This is the main fan that is helping to keep the engine cool. This cooling fan is made from durable plastic and it is sold individually, please note the hardware to secure this item is sold separately.

The 6x8 flange bolt has a lot of applications on various equipment, but is generally designed to secure and lock parts in place. Common on lawn and garden equipment and engines, this flange bolt is silver in color, made of metal, and can become broken over time due to wear and tear. You will need a wrench or socket and torque wrench whe...Read moren making this repair, which is generally easy, but a lot depends on the location and nature of the part it attaches to.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover

This Fuel strainer is an OEM part that is sourced directly from Honda. This part is sold individually and is used to filter the gas of dirt and debris before it enters the engine which can cause the engine to clog. Over time this filter will become clogged itself, therefore, losing its effectiveness in straining the fuel. This part is made of plastic with a foam filter inside.

This flange bolt is a genuine OEM replacement part for use in lawn and outdoor equipment. It has a diameter of 6mm and a length of 12mm. The bolt has a wider circular area that protrudes out from the bolt head, known as a flange. The flange prevents the bolt from moving or loosening during use. Over time the bolt may corrode, crack, or it...Read mores threads may wear down. In this case the bolt will need to be replaced. Visually inspect the other bolts in your equipment to ensure your order the correct number, as each bolt is sold individually. Use a wrench to remove any faulty bolts and install the new bolts in place. Be careful not to overtighten your bolts as you may risk damaging the equipment and the bolt.

This is a genuine Honda replacement part that is intended to be used with small engines. The metal lock pin is used to secure a part assembly like a ball bearing to a shaft like the governor arm. The lock pin is sold as an individual replacement part.

This is an 8mm hex nut, which is a six-sided piece of hardware that connects two parts together in your lawn equipment by keeping screws, bolts, or studs in place. Hex nuts are commonly used in areas of your machine that undergo high stress like in the blade assembly, engine or wheels. If a hex nut is broken, it may be cracked or corroded...Read more, and you may find that you cannot tighten it enough to hold parts in your machine together. If it is not replaced, the parts of your machine may come apart. To remove a hex nut, use a wrench to turn it counterclockwise. Before purchasing this OEM replacement part, keep in mind that this part is sold individually and consult your instruction guide to find out how many nuts your machine needs and where they are located. It is best to replace all the hex nuts at once because they wear out at the same time.