GXV140N2M Honda Lawn Mower - Overview

This is an authentic manufacturer sourced replacement part designed for use with Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

This is an original part from Honda that is used in a small engine. The key sits in the keyway and keeps the flywheel from free spinning when turned. This part is half mooned shaped and is made of metal. This part is sold as an individual replacement part.

This is an authentic manufacturer-sourced component which is designed for use with Honda engines that are commonly installed on a variety of lawn and garden equipment. It is an identical replacement for a damaged or a missing clutch cam that was installed on a new unit. Over time the material will wear out and it may begin to crack eventu...Read moreally requiring a replacement. It is made of high-quality rubber and is sold individually.

The carburetor spacer goes between the carburetor insulator and the carburetor. It is a genuine item that is supplied by the original equipment manufacturer for use with Honda small engines and Toro lawn mowers. This part is made of metal and is sold individually. If this item becomes broken it will need to be replaced and may require a screwdriver during the installation.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This part is an OEM from the Honda manufacturer. The valve rocker arm is made for use with many small engines. This metal component is designed to open and close the valve. Over time it may wear out or get damaged eventually requiring a replacement. The valve rocker arm is sold individually. Please be sure to refer to the specific manual ...Read morefor repair instructions. When replacing the valve rocker arm, a wrench set is necessary.

This is a genuine manufacturer-approved component which is designed for Honda engines that are commonly installed on a variety of lawn and garden equipment. It is an identical replacement for a missing or a damaged oil seal that was installed on a new unit. Refer to the owners manual and the parts diagram for your model to ensure the corr...Read moreect replacement procedure. Note, this high-quality oil seal is made of a durable material and is sold as an individual item. A screwdriver and a wrench set will be needed to perform this repair.

This part is an OEM sourced directly from the manufacturer for use in Honda small engines, lawn mowers, and tillers. The oil pan gasket goes between the cylinder and the oil pan. When replacing this part a screwdriver, a set of pliers, and a socket set might be required during the installation process. It will need to be replaced if it breaks. The gasket is sold individually and is made of a thin material.

This is an authentic replacement part manufactured for use with Honda small engines. The float valve is used to allow fuel into the bowl chamber and to stop the fuel from entering the chamber when it is full. This valve set is sold as an individual replacement part, please see model diagram for associative parts.

This is an original Honda replacement part. The carburetor insulator is designed by the manufacturer for use in engines and lawn mowers. This part is made of high-quality plastic, and is used to protect the carburetor assembly from the heat of the engine. You may require a screwdriver when replacing this item. This product is sold individually.

This star drag spring is a genuine part which is supplied by the original manufacturer for use with Honda engines that are commonly installed on a variety of lawn and garden equipment. The spring applies tension on the connected governor. Over time it can wear out, get damaged or lost eventually requiring a replacement. Check the diagrams...Read more for your model to ensure the correct repair procedure. This spring is made of high-quality metal and is sold individually. A screwdriver and a wrench set might be needed to replace this hardware.