GX360K1DD2 Honda Engine - Overview

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is an authentic Honda replacement part, sourced from the original manufacturer for use with small engines. The special hex head bolt is commonly used to secure the ignition module assembly. This flanged bolt is available as an individual replacement part, please see illustrated part list for associative parts.

This is an authentic item that is supplied by the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

The 6x8 flange bolt has a lot of applications on various equipment, but is generally designed to secure and lock parts in place. Common on lawn and garden equipment and engines, this flange bolt is silver in color, made of metal, and can become broken over time due to wear and tear. You will need a wrench or socket and torque wrench whe...Read moren making this repair, which is generally easy, but a lot depends on the location and nature of the part it attaches to.

This OEM-manufactured flange bolt provides a secure connection between two parts of your equipment. What is different about a flange bolt is that it has a wide, flat flange at the end. This helps to distribute the load being applied to it and prevents the bolt from becoming loose. Flange bolts are commonly found in lawn equipment, but the...Read moreir location varies by the make and model of the machine. When damaged, the part that the flange bolt was holding may loosen and fall off. You also may observe that it the flange bolt is cracked or corroded. It is important for you to replace broken flange bolts immediately as loose or vibrating parts can detach from your equipment while it is operating. You need a socket wrench to remove a flange bolt, as well as rust dissolver or penetrating oil if it is stuck. This replacement part is sold individually so make sure that you consult your user guide to identify where your flange bolts are and how many your equipment needs.

This is an authentic Honda replacement part manufactured for use with small engines. The float valve is used to allow fuel into the carburetor float bowl as it has been drained from the bowl and prevent fuel from entering the bowl when it is full of fuel.

This item is an authentic Honda replacement part that has been sourced from the original manufacturer to be used with small engines. This item is used to provide spacing between the carburetor and the air cleaner assembly. The carburetor spacer is priced as a single item.

This item is a genuine OEM sourced part that has been manufactured to be used with small engines from Honda. The gasket is used to seal the connection between the carburetor and the insulator plate. It is recommended to replace gaskets when servicing the carburetor to make sure the part connections are sealed and seated correctly when the...Read more parts are reassembled. This item is available as an individual replacement part.

This Fuel strainer is an OEM part that is sourced directly from Honda. This part is sold individually and is used to filter the gas of dirt and debris before it enters the engine which can cause the engine to clog. Over time this filter will become clogged itself, therefore, losing its effectiveness in straining the fuel. This part is made of plastic with a foam filter inside.