GX270USMC4 Honda Engine - Overview

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is a genuine replacement part which is supplied by the original equipment manufacturer. It is specially designed for use with Honda engines commonly installed on a variety of lawn and garden equipment. The purpose of it is to filter out dirt and other debris from the fuel that is supplied to the engine. It will over time become clogg...Read moreed and restrict the fuel from getting to the carburetor so it will need to be replaced. It is made of a high-quality plastic and is sold individually. Check the diagrams of your model for the correct installation of the new part.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

It is an identical replacement for a missing or a faulty item that is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. This is a replacement cap-fuel with a metal mesh filter on top, it will help to catch any large contaminants from the fuel. Please make...Read more sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.

This is a genuine OEM sourced replacement part which is specially supplied for use with Honda engines commonly installed on lawn and garden equipment. It is utilized to keep the oil in the tank, it includes a filler to check the oil level. It is a high-quality component which is made of durable plastic and it is sold individually.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This is an authentic replacement part manufactured for use with Honda small engines. The ignition coil creates and electric charge that is sent to the spark plug that creates an arc to ignite the fuel/air mix in the cylinder. A failing or worn out ignition coil will cause difficulty starting the engine and could lead to a non-start situat...Read moreion, and the ignition coil will need to be replaced. This ignition coil is sold as an individual replacement part.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover

This is an authentic Honda replacement part manufactured for use with small engines. The float valve is used to allow fuel into the carburetor float bowl as it has been drained from the bowl and prevent fuel from entering the bowl when it is full of fuel.

This is an original Honda replacement part manufactured for use with small engines. This is the seal for the oil cap/gauge. This intended to be a replacement for a worn out seal and is sold individually, please note the cap is available separately.