GX270RTRSC2 Honda Engine - Overview

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This rubber fuel strainer cup gasket, found in your garden equipment, distributes pressure and creates a seal between the fuel strainer cup and the carburetor so that fuel does not leak. If it is broken, you will notice fuel leakage or a gas smell, and your engine may sputter or have difficulty starting. Unattended fuel leaks not only was...Read morete fuel but also pose a fire hazard. When removing the gasket, make sure that your machine is shut off and has cooled down. Consult your instruction manual to locate the fuel strainer cup, remove mounting screws and clips with a screwdriver, twist the cup slightly, and lift it away. Peel off the old gasket carefully. It is important to be aware that this authentic OEM replacement part is sold individually.

This is a gasket set for various models of small engines. This set of gaskets and O-rings is located within the carburetor assembly for various small engines, and is used to create airtight seals for the carburetor to function properly. This set includes one rubber bowl gasket, four rubber O-rings, and one petcock valve gasket, all from t...Read morehe original equipment manufacturer. These gaskets can wear down over time due to high pressure and temperature exposure, as well as exposure to oil and gas. If you notice poor performance coming from your motor or any leaks near the carburetor, it would be worth inspecting and potentially replacing the gaskets to any other parts being damaged as well. To replace this gasket set, you will first need to disconnect the spark plug, and then the fuel line of the engine. Locate the carburetor and use a wrench to loosen and remove the carburetor bowl. Once the bowl is removed, carefully remove each gasket and O-ring that is worn out and clean the carburetor with carburetor or brake cleaner. Install the new O-rings, and ensure the new gaskets have gasket sealant to prevent leaks. Reinstall the carburetor bowl and secure it with its screw. Install the fuel line and the spark plug, and check the engine for any leaks.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover

This is an authentic Honda replacement part manufactured for use with small engines. The float valve is used to allow fuel into the carburetor float bowl as it has been drained from the bowl and prevent fuel from entering the bowl when it is full of fuel.

This carburetor is an authentic Honda replacement part and is compatible with tilting arbor saws. The carburetor mixes air and gas before the fuel mix goes to the engine. This part is made of metal and plastic and is sold individually. Let the engine cool and drain the gas tank before starting this repair. You may need a screwdriver and a pair of needle nose pliers to aid you in this repair.

This is an authentic Honda replacement part that has been sourced from the original manufacturer to be used with small engines. The metal wingnut is used to fasten the bolt that secures the air cleaner housing. This item may not require tools to install and is priced as a single item.

This item is a genuine OEM sourced part that has been manufactured to be used with small engines from Honda. The gasket is used to seal the connection between the carburetor and the insulator plate. It is recommended to replace gaskets when servicing the carburetor to make sure the part connections are sealed and seated correctly when the...Read more parts are reassembled. This item is available as an individual replacement part.