GX240K1VMT2 Honda Engine - Overview

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is an original Honda replacement part that is manufactured for use with small engines. The purpose of the Air Cleaner Element is to filter dirt and debris from entering the engine and clogging it, therefore, comprimising the performance of the engine. Over time the air cleaner element will clog and needs to be replaced. This foam filter is an individually sold part.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This is an authentic item that is supplied by the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This is a genuine OEM sourced replacement part which is specially supplied for use with Honda engines commonly installed on lawn and garden equipment. It is utilized to keep the oil in the tank, it includes a filler to check the oil level. It is a high-quality component which is made of durable plastic and it is sold individually.

This is an authentic replacement part manufactured for use with Honda small engines. The ignition coil creates and electric charge that is sent to the spark plug that creates an arc to ignite the fuel/air mix in the cylinder. A failing or worn out ignition coil will cause difficulty starting the engine and could lead to a non-start situat...Read moreion, and the ignition coil will need to be replaced. This ignition coil is sold as an individual replacement part.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This is sold as a set that contains five gaskets. They go next to the float chamber. These are genuine OEM sourced parts which are specially designed for use with Honda engines. When replacing these items a set of pliers might be required during the installation process. They are made out of rubber and will need to be replaced if they break.

It is a genuine manufacturer-approved replacement gasket which is designed for use with Honda engines that are commonly installed on lawn and garden equipment. The purpose fo this part is to create an air-tight seal between the carburetor and the stay assembly, please make sure to check appropriate diagrams of your model for correct locat...Read moreion and use of this item. Over time gaskets tend to deteriorate and crack eventually requiring replacement. It is made of durable composite material and it is sold individually.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover