GX240 (Type L1) Honda Engine - Overview

This authentic OEM drain plug washer in your outdoor equipment, with a 12mm diameter, provides a tight seal between the drain plug and the engine to prevent leaks during oil changes. A broken washer will show signs such as oil leakage, visible cracks, or deformations. If left unreplaced, a faulty washer can cause internal damage, loss of ...Read moreoil, and expensive repairs. To replace a damaged washer, you need to first turn off your machine and make sure that its cooled down. Place a drain pan underneath the plug to catch any draining oil. Using a socket wrench, turn the drain plug counterclockwise to loosen it until you can remove it. Please remember that this washer is sold individually.

This is a gasket set for various models of small engines. This set of gaskets and O-rings is located within the carburetor assembly for various small engines, and is used to create airtight seals for the carburetor to function properly. This set includes one rubber bowl gasket, four rubber O-rings, and one petcock valve gasket, all from t...Read morehe original equipment manufacturer. These gaskets can wear down over time due to high pressure and temperature exposure, as well as exposure to oil and gas. If you notice poor performance coming from your motor or any leaks near the carburetor, it would be worth inspecting and potentially replacing the gaskets to any other parts being damaged as well. To replace this gasket set, you will first need to disconnect the spark plug, and then the fuel line of the engine. Locate the carburetor and use a wrench to loosen and remove the carburetor bowl. Once the bowl is removed, carefully remove each gasket and O-ring that is worn out and clean the carburetor with carburetor or brake cleaner. Install the new O-rings, and ensure the new gaskets have gasket sealant to prevent leaks. Reinstall the carburetor bowl and secure it with its screw. Install the fuel line and the spark plug, and check the engine for any leaks.

It is a genuine OEM sourced replacement spark plug which is used with Honda engines commonly installed on lawn and garden equipment. A spark plug is used to deliver electric current from an ignition system to an internal combustion engine. Over time spark plugs tend to wear out, become dirty or fouled eventually requiring a replacement t...Read moreo maintain peak performance. You should gap your spark plug according to the owners manual of the outdoor product you have. This high-quality component is sold individually, please note you would need a spark plug wrench or a socket wrench to install/remove a spark plug.

This genuine OEM sourced replacement carburetor assembly is specially designed for use with Honda engines commonly installed on lawn and garden equipment. The purpose of a carburetor is to mix the air and the gas before the combustible mix goes to the engine. If the engine won\\\'t start and the tank is full of fresh fuel, or if the engin...Read moree starts and then quickly dies, the carburetor is likely the problem. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure the proper air-tight seal for optimum performance. Please note this high-quality metal body carburetor is sold individually.

This is an authentic replacement part sourced directly from the manufacturer. The stop switch wire is commonly found in Honda small engines. This part is made of metal wire with a flexible plastic casing, and is used to send signals from the engine stop switch to the engine. You may require a wrench and pliers when replacing this item. This product is available as an individual replacement part.

It is an authentic OEM sourced replacement filter which is specially produced for use with Honda engines commonly installed on lawn and garden equipment. The purpose of this component is to ensure that the fuel supplied to the unit is free of dust and other harmful components, over time it may get clogged eventually requiring a replacemen...Read moret. It is a durable part which is made of high-quality plastic material and it is sold individually.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover