GX200R Honda Engine - Overview

This is a genuine Honda replacement spark plug. It is sourced directly from original equipment manufacturer and it is sold individually. It is designed to ignite the air fuel mixture by the spark. If spark plugs are not checked with regular services, cleaned or changed when necessary, they can cause problems to occur with the engine. Replacing it you should only need a spark plug socket.

This spark plug creates the spark needed to start compatible small gas engines, it is used in select lawn mowers, generators, snow blowers, and pressure washers, replace a worn or dirty plug if the engine is hard to start, runs rough, or loses power, let the engine cool and remove the plug wire before repair, use the exact engine model number to confirm fit.

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is a genuine manufacturer-sourced replacement component which is specially designed for use with Honda engines commonly installed on lawn and garden equipment. Its purpose is to provide an air-tight seal for the carburetor. Over time gaskets tend to wear out and crack eventually requiring replacement to maintain peak performance. This part is made of high-quality composite material and it is sold individually.

This is an authentic Honda replacement part, sourced from the original manufacturer for use with small engines. The special hex head bolt is commonly used to secure the ignition module assembly. This flanged bolt is available as an individual replacement part, please see illustrated part list for associative parts.

This replacement fuel filter is an authentic OEM part that is specially made for use with Honda engines commonly installed on Toro lawn and garden equipment. The purpose of this part is to filter out dirt and other contaminants from fuel that goes into the carburetor. Over time it may get clogged and restrict the fuel flow eventually requiring replacement. Please note this plastic fuel filter is sold individually.

This genuine Honda part is supplied by the original equipment manufacturer for use with small engines that are commonly installed on a variety of lawn and garden equipment. It provides a tight fit for the frame joint. Please refer to the appropriate diagrams for your model for the exact location and the correct application of this hardwar...Read moree. This is a high-quality washer which is made of durable metal and is sold individually.

This is a genuine replacement part which is supplied by the original equipment manufacturer. It is specially designed for use with Honda engines commonly installed on a variety of lawn and garden equipment. The purpose of it is to filter out dirt and other debris from the fuel that is supplied to the engine. It will over time become clogg...Read moreed and restrict the fuel from getting to the carburetor so it will need to be replaced. It is made of a high-quality plastic and is sold individually. Check the diagrams of your model for the correct installation of the new part.

This genuine OEM oil filler cap assembly is part of your lawn equipment, found commonly on the top or side of the engine. It covers the oil fill hole on the engine so that oil does not spill out and impurities do not get in. A broken cap may be visibly damaged and will not properly seal the oil fill hole. If you do not replace it, the oil...Read more may become contaminated with dirt, reducing the lifespan of your engine. To remove the cap from your machine, gently grip onto it and rotate it counterclockwise. You can lift the cap straight up afterwards. This part is sold individually.

This gasket is a genuine OEM replacement part designed to seal the area between the exhaust pipe and cylinder head. It has a length of 3 inches and a width of 1.5 inches. The gasket prevents exhaust gases produced during combustion from escaping through the connection points and prevents air from entering the exhaust system. A faulty gask...Read moreet will result in increased emission of harmful gases, overheating, increased noise, and overall lower engine performance. You will likely need to remove the exhaust pipe to access the gasket. Once the gasket is removed, clean the surface to ensure a good seal and place the new gasket in position. Reconnect the pipe and ensure all parts are secure.

This is an authentic manufacturer sourced replacement part designed for use with Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

This authentic OEM drain plug washer in your outdoor equipment, with a 12mm diameter, provides a tight seal between the drain plug and the engine to prevent leaks during oil changes. A broken washer will show signs such as oil leakage, visible cracks, or deformations. If left unreplaced, a faulty washer can cause internal damage, loss of ...Read moreoil, and expensive repairs. To replace a damaged washer, you need to first turn off your machine and make sure that its cooled down. Place a drain pan underneath the plug to catch any draining oil. Using a socket wrench, turn the drain plug counterclockwise to loosen it until you can remove it. Please remember that this washer is sold individually.