GX120U1LX2 Honda Lawn Mower - Overview

This is a genuine replacement part which is supplied by the original equipment manufacturer. It is specially designed for use with Honda engines commonly installed on a variety of lawn and garden equipment. The purpose of it is to filter out dirt and other debris from the fuel that is supplied to the engine. It will over time become clogg...Read moreed and restrict the fuel from getting to the carburetor so it will need to be replaced. It is made of a high-quality plastic and is sold individually. Check the diagrams of your model for the correct installation of the new part.

This is an authentic manufacturer sourced replacement part designed for use with Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

This rubber fuel strainer cup gasket, found in your garden equipment, distributes pressure and creates a seal between the fuel strainer cup and the carburetor so that fuel does not leak. If it is broken, you will notice fuel leakage or a gas smell, and your engine may sputter or have difficulty starting. Unattended fuel leaks not only was...Read morete fuel but also pose a fire hazard. When removing the gasket, make sure that your machine is shut off and has cooled down. Consult your instruction manual to locate the fuel strainer cup, remove mounting screws and clips with a screwdriver, twist the cup slightly, and lift it away. Peel off the old gasket carefully. It is important to be aware that this authentic OEM replacement part is sold individually.

This item has been sourced from the original manufacturer, and it is intended to be used with small engines from Honda. The metal spring links with the starter pulley and is used to recoil the roper back around the pulley after the rope is pulled. This item is available as an individual replacement part.

It is an identical replacement for a missing or a faulty item that is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. This is a replacement cap-fuel with a metal mesh filter on top, it will help to catch any large contaminants from the fuel. Please make...Read more sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.

This is a genuine replacement part manufactured for Honda small engines. Replacing carburetor gaskets is recommended when repairing or rebuilding carburetors to ensure proper seals. This gasket set is compatible with several engine model types, and is sold as an individual set.

This part is a genuine OEM item that has been sourced to be used with Honda small engines. This spacer is used as a link between the carburetor and the air cleaner elbow. The carburetor spacer is priced as an individual part, please note associative parts are available separately.

This is an original part from Honda that is used in a small engine. The key sits in the keyway and keeps the flywheel from free spinning when turned. This part is half mooned shaped and is made of metal. This part is sold as an individual replacement part.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

The flange bolt is used to secure parts together in a variety of lawn and garden outdoor equipment. It is sourced directly from the manufacturer and has a diameter of 6mm and a length of 12mm. The bolt is made of metal and has a ring-shaped rim on one end known as a flange. This flange helps to secure the bolt in place and prevents it fro...Read morem falling off during use. Inspect all the bolts on your equipment as you may need more than one. If you note that any of them are deformed, corroded or the threads are worn down, you will need to replace them as each bolt is sold individually. Remove the damaged bolt and thread the new one on with your hands before tightening with a wrench.

This is an authentic replacement part manufactured for use with Honda small engines. The float valve is used to allow fuel into the bowl chamber and to stop the fuel from entering the chamber when it is full. This valve set is sold as an individual replacement part, please see model diagram for associative parts.

This is an authentic Honda replacement part that has been sourced from the original manufacturer to be used with small engines. The metal wingnut is used to fasten the bolt that secures the air cleaner housing. This item may not require tools to install and is priced as a single item.