GT-1000 Echo Trimmer - Overview

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This is a genuine manufacturer approved replacement drive shaft that is designed for Echo string trimmers. Flexible drive shaft fits inside the drive shaft housing to spin the cutting head. It is made out of metal and it is sold individually. To complete this repair you would need a screwdriver and pliers. Removing the Drive Shaft: • ...Read moreLoosen the shaft screws. • Remove the air filter. • Remove the throttle cable. • Remove the ignition wires. • Remove the shaft housing. • Remove the drive shaft. Installing the New Drive Shaft: • Lubricate the drive shaft. • Install the new drive shaft. • Re-install the shaft housing. • Re-install the throttle cable and ignition wires. • Re-install the air filter assembly.

This is an original part from Echo. The metal rewind spring is made for use with a variety of lawn and garden engines. This item is fitted between the recoil drum and the starter plate in the starter assembly. This component rewinds the starter rope after has been pulled to start the motor. A screwdriver is required for the repair. The rewind spring is sold individually.

This is an authentic OEM supplied replacement starter rope that is produced for use with Echo gas powered equipment. It is the part of the recoil starter mechanism which allows user to pull-start the engine. One durable nylon rope is included per order, please note the plastic grip handle is sold separately.

This replacement grommet is an authentic OEM item that is produced for use with Echo gas powered equipment. It fits in the fuel tank to secure the hose and seal the opening. Over time it may deteriorate and crack eventually requiring replacement. It is made from durable rubber material and it is sold individually.

This control-throttle is a genuine OEM sourced item designed for Echo handheld lawn and garden equipment. This is the plastic lever that allows user to control the throttle. It is made from durable plastic and it is sold individually. You will need a screwdriver to replace this part.

This spark plug boot is an authentic OEM supplied replacement part, not an aftermarket equivalent. This rubber cap helps is used to connect the spark plug to the armature-magneto. Over time rubber material can dry out and crack requiring replacement. Please note, this part is sold individually.

This is an original Echo replacement part manufactured for use with outdoor power equipment. This special screw includes a washer and can be used with either flat or phillips head drivers. The screw has different applications, please see model diagram for part location and use. The screw is sold individually.

This manufacturer sourced replacement part is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This is a standard hardware which will has multiple applications depending on your equipment. This lock nut is made from high quality metal and it is sold individually.

This is a genuine Echo replacement part that has been sourced from the original manufacturer and is intended to be used with trimmers. The metal spring is part of the throttle handle assembly and is used to provide torsion to the throttle lever. This item is needed to allow the trigger to return and release the valve. This item is available as an individual replacement part.