GSD1000-04 Hotpoint Dishwasher - Overview
Sections of the GSD1000-04
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Lower Front Dishrack Wheel
PartSelect #: PS259136
Manufacturer #: WD12X271
The lower dishrack wheel on your dishwasher allows the dishrack to roll in and out effectively. If your lower dishrack wheels are damaged, or the rack does not roll in and out, you may need to replace...
$30.53
In Stock
Corner Tub Baffle - Lower Right
PartSelect #: PS263963
Manufacturer #: WD8X227
This baffle fits the lower right hand corner of some dishwashers. It is black rubber and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and righ...
$24.67
In Stock
Corner Tub Baffle - Lower Left
PartSelect #: PS263964
Manufacturer #: WD8X228
The corner tub baffle may also be known as the door baffle and is a part used on your dishwasher. The left and right side baffle on your dishwasher should be installed and replaced at the same time. T...
$24.67
In Stock
Silverware Basket (Grey)
PartSelect #: PS261346
Manufacturer #: WD28X265
The silverware basket, used for dishwashers, is in the bottom of the dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, you sh...
$79.80
In Stock
Dishwasher Water Inlet Valve
PartSelect #: PS259411
Manufacturer #: WD15X93
This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or ...
$52.98
Special Order
Third Level Spray Arm
PartSelect #: PS755622
Manufacturer #: WD28X10103
Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack. This spray ar...
$55.29
Special Order
Rinse Aid Injector Container With Gasket
PartSelect #: PS2345692
Manufacturer #: WD35X10346
This part attaches to the inner door panel.
$49.50
On Order
Fine Thread Telescoping Tower Power
PartSelect #: PS260569
Manufacturer #: WD22X120
This telescoping power tower comes in three sections.
No Longer Available
Float Switch
PartSelect #: PS260235
Manufacturer #: WD21X479
Water that fills your dishwasher lifts this float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off...
$20.37
In Stock
Lower Spray Arm
PartSelect #: PS260584
Manufacturer #: WD22X135
This dishwasher spray arm is for the bottom of your dishwasher. Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying wa...
No Longer Available
Common Symptoms of the GSD1000-04
[Viewing 6 of 6]Leaking
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel broken off bottom rack
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
Parts Used:
-
Julie from Maumee, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
503 of 520 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers fell off lower rack of dishwasher.
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.
Parts Used:
-
Lloyd from The Villages, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
369 of 371 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)
1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to g ... Read more ain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to g ... Read more ain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
Read less
Parts Used:
-
Don from Mount Vernon, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
71 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!