This white plastic right side end cap supports the 2 liter bottle rack rail inside the refrigerator door. It attaches to the inner door liner to hold the rail in position and help keep bottles and containers on the shelf when the door moves. Cracks, broken tabs, or damage around the mounting area may allow the rail to loosen or detach. In...Read morespect the cap and door attachment points before replacement. This support fits the right end of the rail. Check that it is secure before returning items to the shelf. This is an OEM part sourced directly from the manufacturer.
This white plastic left side end cap supports the 2 liter bottle rack rail inside the refrigerator door. It holds the rail against the inner door panel to help keep bottles and containers on the shelf when the door moves. Cracks, broken locking tabs, or a damaged mounting area may let the rail come loose. Inspect both the cap and the door...Read more attachment points before replacement. This cap fits the left end of the rail. Check that the replacement is fully secured before returning items to the shelf. This is an OEM part sourced directly from the manufacturer.
This white door shelf retainer bar keeps bottles, jars, and other containers on the refrigerator door shelf when the door moves. It is supplied at approximately 20.25 inches long and must be cut to fit the required shelf width and end caps. The end caps are not included and must be ordered separately if needed. A bent, broken, or damaged ...Read morebar may no longer hold items securely. Check the existing end caps before reusing them, and confirm the finished length before cutting the replacement bar. This is an OEM part sourced directly from the manufacturer.
This 120 volt, 60 hertz defrost timer switches the refrigerator into a 30 minute defrost cycle after eight hours of compressor run time. The cycle allows the heater to clear frost from the evaporator so air can circulate. A faulty timer may allow frost buildup that restricts airflow and leaves the refrigerator or freezer too warm. It may ...Read morealso fail to return the appliance to cooling. Confirm the timer fault before replacement, since other defrost components can cause similar symptoms. Disconnect power before accessing the control. This is an OEM part sourced directly from the manufacturer.
This white plastic right side end cap secures the door shelf retainer bar to the refrigerator door. It measures approximately 3 inches by 4 inches and supports the specified gallon sized door rack. Cracks, broken sections, or damaged mounting areas may let the bar loosen, leaving stored items without proper restraint when the door moves. ...Read moreInspect the cap, rail, and door attachment points before replacement. This part fits the right end only; the left cap is sold separately. Check that the replacement is secure before loading the shelf. This is an OEM part sourced directly from the manufacturer.
This white plastic left side end cap secures the refrigerator door shelf retainer bar. The bar helps keep bottles, jars, and larger containers on the shelf when the door moves. Cracks, broken sections, or damage around the mounting area may leave the bar loose or unsupported. Inspect the cap, retainer bar, and door attachment points befor...Read moree replacement. This part fits the left end of the specified rail. Match the shelf position to the appliance parts diagram and check that the replacement is secure before loading the shelf. This is an OEM part sourced directly from the manufacturer.
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
Steady compressor operation relies on the electrical support provided by this refrigerator run capacitor. It creates a phase shift in the motor circuit to help the compressor run as designed while circulating refrigerant through the cooling system. A failed capacitor may contribute to unusual humming, difficulty starting, or reduced cooli...Read moreng performance. Replacing a faulty capacitor helps restore proper electrical conditions for compressor operation. The component stores electrical energy and can retain a charge after power is disconnected, requiring care during handling and replacement. This is an OEM part sourced directly from the manufacturer.
Cold air moves through the food compartments with help from this refrigerator evaporator fan motor kit. The motor drives the fan that circulates air across the evaporator coils and distributes cooled air through the freezer and fresh food sections. A worn or failed motor may cause squealing, buzzing, reduced airflow, or warmer compartment...Read more temperatures. Replacing a faulty motor helps restore air circulation and more even cooling. The kit includes the motor, two retainer clips, three terminal connectors, and an installation instruction sheet. This is an OEM part sourced directly from the manufacturer.
Cooling problems or a failure to defrost can point to an issue in the refrigerator defrost system, but they do not confirm this thermostat is the cause. During defrost, the thermostat helps protect the evaporator from overheating. This is an OEM kit. Unplug the refrigerator before installation.
To secure a refrigerator or freezer door handle to the door, this OEM kit includes four #10-16 screws. Each is 0.500 in. long and has a Phillips or square drive. Confirm compatibility with your appliance before buying.
A refrigerator or freezer door handle is held in place by this screw. The OEM part has a #10-16 thread, a 1/2-inch length, and a Phillips/Square drive. Confirm it matches your appliance before ordering.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
tenants had broken door brackets in fridge
933 of 939 peoplefound this instruction helpful.
Nancy from Pleasant Prairie, WI
A Bit Difficult
15 - 30 mins
cut brackets to size and snapped them into place with the caps purchased. I will continue to use PartSelect for all my appliance repair needs. Not only did I receive my order within 2 days but the cost was over half of what I have been paying for the local parts store to order for me. Thank you PartsSelect.
Retainer bar had broken from overloading the door with water bottles.
732 of 741 peoplefound this instruction helpful.
Nancy L from Gainesville, FL
Really Easy
Less than 15 mins
It took longer to remove the retainer bar from the packaging than it did to install it in the fridge.
Both left and right end caps were pushed into their respective places on the retainer bar and then the whole thing was snapped into place on the door of the fridge.
Put them together and (do this carefully, as they are light-duty plastic; the reason the originals failed) snapped them into place. Parts were factory-origninal, easy to figure out. Delivery time was exceptional, packaging great.