This white door shelf end cap supports the retainer bar inside a refrigerator or freezer door. It fits either the left or right end of the specified shelf rail and helps keep bottles and containers in place when the door moves. Cracks, broken tabs, or a damaged mounting area may let the bar come loose. Inspect the cap, rail, and door atta...Read morechment points before replacement. Secure the new support in its mounting track, then check that the retainer bar is firmly seated before returning items to the shelf. This is an OEM part sourced directly from the manufacturer.
This 120 volt, 60 hertz defrost timer switches the refrigerator into a 30 minute defrost cycle after eight hours of compressor run time. The cycle allows the heater to clear frost from the evaporator so air can circulate. A faulty timer may allow frost buildup that restricts airflow and leaves the refrigerator or freezer too warm. It may ...Read morealso fail to return the appliance to cooling. Confirm the timer fault before replacement, since other defrost components can cause similar symptoms. Disconnect power before accessing the control. This is an OEM part sourced directly from the manufacturer.
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
This white door shelf retainer bar keeps bottles, jars, and condiments on the shelf when the refrigerator or freezer door moves. It is supplied at approximately 30.75 inches long and 1.75 inches wide and can be cut to the required length. A bent, broken, or loose bar may leave stored items without proper restraint. Inspect the end support...Read mores as well before replacement, since damaged caps can prevent the bar from staying secure. Confirm the finished length and mounting arrangement before trimming and fitting the replacement rail. This is an OEM part sourced directly from the manufacturer.
Steady compressor operation relies on the electrical support provided by this refrigerator run capacitor. It creates a phase shift in the motor circuit to help the compressor run as designed while circulating refrigerant through the cooling system. A failed capacitor may contribute to unusual humming, difficulty starting, or reduced cooli...Read moreng performance. Replacing a faulty capacitor helps restore proper electrical conditions for compressor operation. The component stores electrical energy and can retain a charge after power is disconnected, requiring care during handling and replacement. This is an OEM part sourced directly from the manufacturer.
This is the replacement crisper drawer cover support for your refrigerator. The crisper shelf rests on the support, which keeps it level. If your drawer cover or shelf will not stay level, or will not stay in place, the support may be damaged. The support is held in place on the refrigerator wall with a drive pin. To remove the damaged su...Read morepport, simply drive the pin all the way in, and use a putty knife to pry the support from the refrigerator wall. At this point, pull the drive pin out and replace the old support with the new one. This is an OEM part and is sold individually.
This crisper drawer frame is designed to support the crisper pan and hold the glass shelf above it, helping maintain organization and airflow within your refrigerator. Made of durable white plastic with a raised edge, it fits select models from Frigidaire, Kenmore, Gibson, and Electrolux. Please note that this replacement part includes th...Read moree frame only; the glass shelf is sold separately. For proper installation, simply remove the old frame and position the new one in place.
This evaporator fan blade moves cooled air through the refrigerator or freezer compartments when driven by the fan motor. A cracked, warped, or loose blade may vibrate, strike nearby parts, or fail to move enough air. Unusual ticking or humming noises and warmer compartment temperatures may be reasons to inspect the fan assembly. Check fo...Read morer ice buildup and motor or mounting problems as well, since these can cause similar symptoms. Disconnect power before accessing the blade and follow the appliance instructions for fitting it securely on the motor shaft. This is an OEM part sourced directly from the manufacturer.
This plastic ice cube tray holds water for freezing into 12 cubes at a time. Channels help water spread evenly during filling, while corner supports allow trays to stack securely in the freezer. The tray measures approximately 11 inches long and 4.5 inches wide and is sold individually. Its flexible design allows frozen cubes to be releas...Read moreed by hand. Cracks or splits may let water leak before it freezes and are reasons to replace the tray. Check the available freezer space against the tray dimensions before ordering. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Clicking sound then within a minute clicking again, not cooling.
81 of 97 peoplefound this instruction helpful.
Melvin from Semmes, AL
Easy
Less than 15 mins
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it r
... Read moreattles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.
Read less
Was this helpful?
Thank you for voting!
Side-by-side .. freezer working, fridge not cooling
48 of 52 peoplefound this instruction helpful.
Tad from Lancaster, OH
Easy
15 - 30 mins
Screw drivers
My freezer was frozen but my refrigerated side was not cooling, the temp was actually around 60-degrees. After inspecting i noticed no air was flowing through the vent from freezer side to fridge side. I removed everything from freezer and took the back wall panel off inside freezer section and immedietely noticed alot of ice on coils etc
... Read more. After researching i found the defrost timer was not working and thus allowing frost and ice to build up on coils and block air flow. My defrost timer was located on the front bottom left behind kick panel, using a phillips screwdriver i removed 2 screws and then disconnected wire harness to the defrost timer. Then i inserted new defrost timer and connected wire harness and then put the 2 screws back in. My fridge is now working great and the ice build-up is gone and i am getting good air flow .. temps on fridge side are now between 32-34degrees. This was an easy project and saved me alot of money doing myself
Read less
Was this helpful?
Thank you for voting!
Wouldn't hold temp.
49 of 58 peoplefound this instruction helpful.
Laurence from Overland Park, KS
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
I'm too young to die so I unpluged the refriderator first. The cold control is mounted in a plastic housing at the top of the freezer compartment that is held in place by two screws on the back side. I removed them with a nutdriver. Pull off the knob and use a screwdriver to release the control from it's bracket and pull off the 3 wire
... Read mores noteing where they go. Slide the sensing element out and remove the plastic sleeve. Stragihten the sensing element on the new control and slide on the plastic sleve. Slide the sensing element in place, push the wires onto the terminals and snap the control into the bracket. Re-install the two screws and the control knob. Plug it in and you're done. It took longer to write this than to replace the control.