This OEM cup filter is designed to be compatible with all rear-filter refrigerators made before April 2001. The filter fits into a round white plastic housing. For this repair you may also require the PS428513 wrench or PS428532 O-ring. To install you will need to unscrew the cup before you can see the old filter, and then dump the water....Read more Pull the old filter straight down and place the new filter inside the filter cup. The end of the filter with the O-ring should be directed upward. As you tighten the filter it will align itself. If your refrigerator has a Change Filter light, it will need to be reset. Press and hold this button until the green light flashes (up to 15 seconds). This filter has a 2-Inch depth, 4.25-Inch height, 2-Inch width and needs to be replaced every 6 months of use or 200 gallons depending on which comes first. Filters for: Taste and odor Sediment 99.3% of Lead 99.99% of Cysts 99.7% of Turbidity 99.8% of Particulates (Class I) 94.9% of Atrazine (a herbicide) 94.2% of 2,4-D (a herbicide) 97.8% of Chlorine (Class I) 87.5% of Toxaphene (a pesticide).
This white door shelf end cap supports the retainer bar inside a refrigerator or freezer door. It fits either the left or right end of the specified shelf rail and helps keep bottles and containers in place when the door moves. Cracks, broken tabs, or a damaged mounting area may let the bar come loose. Inspect the cap, rail, and door atta...Read morechment points before replacement. Secure the new support in its mounting track, then check that the retainer bar is firmly seated before returning items to the shelf. This is an OEM part sourced directly from the manufacturer.
This 120 volt, 60 hertz defrost timer switches the refrigerator into a 30 minute defrost cycle after eight hours of compressor run time. The cycle allows the heater to clear frost from the evaporator so air can circulate. A faulty timer may allow frost buildup that restricts airflow and leaves the refrigerator or freezer too warm. It may ...Read morealso fail to return the appliance to cooling. Confirm the timer fault before replacement, since other defrost components can cause similar symptoms. Disconnect power before accessing the control. This is an OEM part sourced directly from the manufacturer.
This white plastic door shelf end cap holds the retainer bar in place inside the refrigerator door. It fits either the left or right end of the specified shelf rail and is sold individually. Cracks, broken tabs, or damage around the mounting area may allow the bar to loosen, leaving bottles and containers without proper restraint. Inspect...Read more the cap, rail, and door attachment points before replacement. Fit the new cap into the matching position and check that both the support and bar are secure before loading the shelf. This is an OEM part sourced directly from the manufacturer.
This refrigerator defrost thermostat is a genuine OEM part and is sourced directly from the manufacturer. Located on the back wall of the freezer section in the refrigerator, the defrost thermostat is used to regulate the appliances temperature to keep the refrigerator cold and constant. The part is made of plastic, and has a 4 inch termi...Read morenal on the white lead and a 6 inch terminal on the red lead. A refrigerator defrost thermostat may need to be replaced if the appliance is experiencing temperature related issues such as: too cold, too warm, frost buildup, not running, or running too long.
This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the l...Read moreimit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
Steady compressor operation relies on the electrical support provided by this refrigerator run capacitor. It creates a phase shift in the motor circuit to help the compressor run as designed while circulating refrigerant through the cooling system. A failed capacitor may contribute to unusual humming, difficulty starting, or reduced cooli...Read moreng performance. Replacing a faulty capacitor helps restore proper electrical conditions for compressor operation. The component stores electrical energy and can retain a charge after power is disconnected, requiring care during handling and replacement. This is an OEM part sourced directly from the manufacturer.
This ice container and auger assembly collects and stores ice in the freezer, then moves it toward the door dispenser. The assembly includes the bucket, rotating auger, and crusher mechanism. A cracked container, damaged auger, or broken internal part may cause jams or prevent ice from dispensing. Check for clumped ice and inspect the mot...Read moreor coupling as well, since these can cause similar symptoms. Turn off the ice maker before removing the old bucket, and follow the appliance instructions to align and fully seat the replacement assembly. This is an OEM part sourced directly from the manufacturer.
Fresh ice is produced automatically by this refrigerator ice maker assembly, which fills its mold, freezes water, and releases cubes into the storage bin. Its heat release mechanism briefly warms the mold to loosen the ice during harvesting. A damaged or failed assembly may stop cycling, leave cubes stuck in the mold, or leak into the buc...Read moreket. Replacing a faulty unit helps restore automatic ice production. The assembly includes a wiring harness and adapter plug to support the electrical connections used by the replacement kit. This is an OEM part sourced directly from the manufacturer.
This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nu...Read moret driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.
This is the door shelf end cap for your refrigerator. It connects to the refrigerator door and keeps the door bar in place. Your refrigerator will have two shelf end caps, one for the right side and one for the left. This part is the right side door shelf end cap. It is made of white plastic and is a little over one inch long. This is an OEM part from the manufacturer and is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water in Frig was tasting bad.
499 of 504 peoplefound this instruction helpful.
Patricia from Fulton, MO
Really Easy
Less than 15 mins
I turned the cap for the old filter and pulled it out . Then I put in the new one in and turned the cap to secure it in frig.
Was this helpful?
Thank you for voting!
water from refigerator dispenser started tasting bad
369 of 370 peoplefound this instruction helpful.
Anthony from Springfield, VA
Easy
Less than 15 mins
I removed the top shelf in the fridge. I then unscrewed the cover to the water filter and pulled the filter cartridge down into the cover. Keep the cover upright as there may be some water in it. I carried it to the sink. I took the new cartridge and ran water through it from the sink, then set it in the cover and took it to the fridg
... Read moree. I pushed the cartridge up into the space that I removed the old one from and screwed the cover back on. Then I took an empty pitcher and filled it from the water dispenser in the fridge door. I did this three times to charge the filter and remove charcoal dust. Water tastes great now. I ordered two filters so I would ony have to buy once a year. Great site to order the filters from. Cheaper than other sources and delivery was quick.
Read less
Was this helpful?
Thank you for voting!
Broken ice maker
255 of 345 peoplefound this instruction helpful.
Juan from Miami, FL
Really Easy
15 - 30 mins
Socket set
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.