This white door shelf end cap supports the retainer bar inside a refrigerator or freezer door. It fits either the left or right end of the specified shelf rail and helps keep bottles and containers in place when the door moves. Cracks, broken tabs, or a damaged mounting area may let the bar come loose. Inspect the cap, rail, and door atta...Read morechment points before replacement. Secure the new support in its mounting track, then check that the retainer bar is firmly seated before returning items to the shelf. This is an OEM part sourced directly from the manufacturer.
This 120 volt, 60 hertz defrost timer switches the refrigerator into a 30 minute defrost cycle after eight hours of compressor run time. The cycle allows the heater to clear frost from the evaporator so air can circulate. A faulty timer may allow frost buildup that restricts airflow and leaves the refrigerator or freezer too warm. It may ...Read morealso fail to return the appliance to cooling. Confirm the timer fault before replacement, since other defrost components can cause similar symptoms. Disconnect power before accessing the control. This is an OEM part sourced directly from the manufacturer.
This white plastic door shelf end cap holds the retainer bar in place inside the refrigerator door. It fits either the left or right end of the specified shelf rail and is sold individually. Cracks, broken tabs, or damage around the mounting area may allow the bar to loosen, leaving bottles and containers without proper restraint. Inspect...Read more the cap, rail, and door attachment points before replacement. Fit the new cap into the matching position and check that both the support and bar are secure before loading the shelf. This is an OEM part sourced directly from the manufacturer.
This refrigerator defrost thermostat is a genuine OEM part and is sourced directly from the manufacturer. Located on the back wall of the freezer section in the refrigerator, the defrost thermostat is used to regulate the appliances temperature to keep the refrigerator cold and constant. The part is made of plastic, and has a 4 inch termi...Read morenal on the white lead and a 6 inch terminal on the red lead. A refrigerator defrost thermostat may need to be replaced if the appliance is experiencing temperature related issues such as: too cold, too warm, frost buildup, not running, or running too long.
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
Steady compressor operation relies on the electrical support provided by this refrigerator run capacitor. It creates a phase shift in the motor circuit to help the compressor run as designed while circulating refrigerant through the cooling system. A failed capacitor may contribute to unusual humming, difficulty starting, or reduced cooli...Read moreng performance. Replacing a faulty capacitor helps restore proper electrical conditions for compressor operation. The component stores electrical energy and can retain a charge after power is disconnected, requiring care during handling and replacement. This is an OEM part sourced directly from the manufacturer.
This evaporator fan blade moves cooled air through the refrigerator or freezer compartments when driven by the fan motor. A cracked, warped, or loose blade may vibrate, strike nearby parts, or fail to move enough air. Unusual ticking or humming noises and warmer compartment temperatures may be reasons to inspect the fan assembly. Check fo...Read morer ice buildup and motor or mounting problems as well, since these can cause similar symptoms. Disconnect power before accessing the blade and follow the appliance instructions for fitting it securely on the motor shaft. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer would not defrost
185 of 208 peoplefound this instruction helpful.
Roger from Orangevale, CA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
My freezer would freeze up and not allow cold air to refrigerator side. First I took off bottom face plate, located the timer on left side bottom, removed the two screws and unpluged the timer. Replaced the timer with new one. Second I removed all food from freezer. Took of back of freezer wall with nut driver. Located the thermostat whic
... Read moreh was very easy to remove. Just one clip holding thermostat. Unplugged the two wires from the old thermostat and plugged in new wires. Thanks to Partselect.com, the parts were an exact match. Very easy to do. Saved my tons of money. Freezer and refer works like new.
Freezer coil frosting up solid. Refrigerator warming
106 of 118 peoplefound this instruction helpful.
Michael from Newark, OH
A Bit Difficult
1- 2 hours
Nutdriver
First - I asked a person familiar in ref/freezer repair for assistance. This was the hardest issue - trying to find someone to offer "free" advise. He stated that when this problem occurs it is usually one of two things: 1) The defrost timer (underneath Refrigerator - Attached w/2 screws and plug-n connector) not functioning or 2) The de
... Read morefrost sensor (clipped-on to the coolant line (2-press-on wires) above the main coolant coil in in rear of freezer section behind panel secured w/5 1/4" hex-head screws) not properly sensing need for defrosting. The Tech. also stated that the defrost/heat coil, which surrounds the large coolant coil in the back of the freezer hardly ever goes bad unless it is the glass/clear type coil which often crack. (Mine was the black filament type element like found in an electric oven). I check the element with an ohm meter - 27 ohms of resistance which indicated it was okay). I replaced both defrost timer & defrost sensor at the same time and that fixed the problem. Parts ordered were an exact match to originals (dispite model number changes/upgrades) and everything went very well. NOTE: It is good to have the part numbers off of each original item and know what they are called before placing your order. All fixed for less than $50.00. A service call alone would be more than this. Took about 2 hours to do, due to having to defost the iced-up freezer coil w/a hair blower. Don't use sharp objects to chip away ice, let the blower do the work - Patience and a couple of towels to absorb water is important here. Hope this helps the other do-it-yourselfers.
Side-by-side .. freezer working, fridge not cooling
48 of 52 peoplefound this instruction helpful.
Tad from Lancaster, OH
Easy
15 - 30 mins
Screw drivers
My freezer was frozen but my refrigerated side was not cooling, the temp was actually around 60-degrees. After inspecting i noticed no air was flowing through the vent from freezer side to fridge side. I removed everything from freezer and took the back wall panel off inside freezer section and immedietely noticed alot of ice on coils etc
... Read more. After researching i found the defrost timer was not working and thus allowing frost and ice to build up on coils and block air flow. My defrost timer was located on the front bottom left behind kick panel, using a phillips screwdriver i removed 2 screws and then disconnected wire harness to the defrost timer. Then i inserted new defrost timer and connected wire harness and then put the 2 screws back in. My fridge is now working great and the ice build-up is gone and i am getting good air flow .. temps on fridge side are now between 32-34degrees. This was an easy project and saved me alot of money doing myself