GR871 (Type 3) DeWALT Chop Saw - Overview

This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on t...Read morehe tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This M8 × 1.25 elastic stop nut (lock nut) is an OEM replacement fastener used on power tools to securely hold critical components in place while resisting loosening from vibration. Designed with an integrated nylon insert, it provides reliable locking force without the need for additional hardware and is ideal for replacing worn or missing nuts during maintenance or repair to ensure safe, stable operation.

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

This is a genuine OEM approved replacement part designed for use with chop saws. This item holds carbon brush against the armature. It is made out of plastic with metal and it is sold individually. Please note carbon brushes are sold separately. To replace this assembly you would need a screwdriver and pliers. • First remove screws ho...Read morelding the cover together • Carefully remove two halves of the housing to gain access to armature and brush holder • Remove the screws holding brush holder to the trigger • Remove the armature assembly and the brush holder • Install the new brush holder, brushes and the armature • Reassemble and test your tool

This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brush...Read morees are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Help restore reliable motor performance with this carbon brush, designed to maintain electrical contact between the motor's stationary and rotating components. As brushes wear naturally over time, replacing a worn brush can help resolve issues such as power loss, excessive sparking, intermittent operation, or motor failure. This replaceme...Read morent brush helps ensure efficient power transfer and consistent tool performance. Because most compatible tools use two brushes, replacing both at the same time is recommended for balanced wear and optimum operation. Refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

This screw is commonly used on a variety of power tools. It is a genuine OEM sourced replacement part. Please make sure to check appropriate diagrams for correct location and use of this screw. Includes one pan head screw per order. You will need a screwdriver to install or remove it.

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on t...Read morehe tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a DeWALT replacement part directly sourced from the manufacturer for use in saws. The clamp washer goes between the blade adapter and the blade clamp. A screwdriver might be needed during the installation process. It is made of metal and will require replacing if it becomes broken. This is available as an individual replacement part but keep in mind that two may be needed.