This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can...Read more be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance.
To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
This spring is located on the mullion, or door flap, of your fridge. This spring is sourced from the genuine OEM manufacturer for various refrigerator models. It measures about 1.5 inches in total length, and is made entirely out of metal.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This ice maker assembly kit is a genuine OEM replacement designed for select LG refrigerators. Engineered to produce ice efficiently, it features a built-in thermostat and heating element that work together to freeze water and release ice cubes from the mold. With a capacity to produce up to 14 cubes per cycle, this assembly ensures a con...Read moresistent and reliable supply of ice. Installation is straightforward and suitable for DIY repairs, though model compatibility should be verified prior to purchase. Crafted to meet LG’s performance standards, this kit offers dependable operation and long-term durability.
NOTE: The Secondary (smaller) wire connector has 3 wires in it. If original ice maker has 6 wire connector see part number AEQ73110205. Please verify connector before ordering.
This fan assembly circulates air through the appliance to support proper temperature control and ventilation. Designed for quiet and efficient airflow, it is replaced when airflow weakens, noise increases, or cooling performance declines.
This is a water filter bypass plug made for use with LG refrigerators. This plug is designed to act as a stand-in and allow water to flow to the dispenser or ice maker, even when the water filter is removed. This plug is made of white plastic and measures approximately 7 inches long and 1.2 inches wide. Installing this water filter bypass...Read more plug is simple, and only requires that you remove any present water filters, and then stick this plug in its place, and close the filter housing.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace leaking water inlet valve assembly
42 of 75 peoplefound this instruction helpful.
Richard from JACKSONVILLE, FL
Really Easy
15 - 30 mins
Screw drivers
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new
... Read morewater inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Read less
Was this helpful?
Thank you for voting!
Door flap spring
12 of 23 peoplefound this instruction helpful.
Claudio from YONKERS, NY
Really Easy
Less than 15 mins
Pliers
Insert the top first and then twist to insert bottom
Was this helpful?
Thank you for voting!
old one broke
9 of 17 peoplefound this instruction helpful.
Ron from MAXWELL, IN
Easy
30 - 60 mins
Screw drivers
Sent for replacement,got it took old one off put new one on that was it. Thank you