GR-J308MMYM (AMTCNA0) LG Refrigerator - Overview
Sections of the GR-J308MMYM
[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Handle Screw
PartSelect #: PS8752913
Manufacturer #: MJB63190001
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your...
$15.00
In Stock
Freezer Door Gasket
PartSelect #: PS11758511
Manufacturer #: MDS38201426
This genuine freezer door gasket helps create an airtight seal around the freezer compartment, preventing warm air and moisture from entering while keeping cold air inside for efficient cooling perfor...
$80.82
In Stock
Door Gasket Assembly
PartSelect #: PS11732674
Manufacturer #: ADX72930461
This is a door seal, also known as a door gasket, for LG refrigerators. This door gasket is used to seal the warmer room temperature from the cooler fridge interior. If the gasket for your refrigerato...
$101.29
In Stock
GASKET ASSEMBLY,DOOR
PartSelect #: PS11732673
Manufacturer #: ADX72930460
This fridge gasket, also known as a door seal, is an authentic OEM part supplied by LG for use with various models of LG refrigerators. It is a flexible strip of rubber that sits along the perimeter o...
$101.29
In Stock
Clip
PartSelect #: PS3522801
Manufacturer #: 4004JA3002A
This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing i...
$31.58
On Order
Ice Maker Assembly Kit
PartSelect #: PS12724823
Manufacturer #: AEQ73110219
This genuine OEM ice maker assembly is compatible with various models of LG refrigerators. The assembly includes the icemaker unit, ice mold, water inlet valve, ice bin, thermostat, and wiring harness...
$184.05
In Stock
STOPPER,DOOR
PartSelect #: PS7796195
Manufacturer #: MJB62830601
This is a door stopper designed for LG refrigerators. This white plastic stopper is made to ensure the refrigerator door closes properly. If your fridge door is not closing entirely, or if this closer...
$15.00
In Stock
ICE BUCKET
PartSelect #: PS18029854
Manufacturer #: AKC73369914
This ice bucket assembly is designed to store and dispense ice within select refrigerator models. It includes both the ice bin and the auger mechanism, which rotates to push ice through the dispenser ...
$183.94
On Order
Common Symptoms of the GR-J308MMYM
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Door Sweating
Fixed by
these parts
these parts
Show All
Door won’t open or close
Fixed by
these parts
these parts
Show All
Ice maker not making ice
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Ice maker won’t dispense ice
Fixed by
these parts
these parts
Show All
Frost buildup
Fixed by
these parts
these parts
Show All
Freezer section too warm
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Evaporator fan making noise
Turn off the power to the refrigerator. Remove the back plate. Unplug the fan motor. Remove the fan housing and pull the fan blade from the motor. Replace the motor by removing 4 screws. Replace with the new motor and reinstall the fan blades. Secure the fan housing, plug the fan motor, and screw on the back panel. Plug and go!
Parts Used:
-
Tom from COPPER HILL, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced Old Molded Gasket with new one
For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.
For the left side, needed a Phillip’s screwdriver to remove the flap first. H ... Read more elps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.
Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.
For the left side, needed a Phillip’s screwdriver to remove the flap first. H ... Read more elps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.
Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.
Read less
Parts Used:
-
Megan from Elk Grove, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Moldy and torn gaskets
Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.
Parts Used:
-
Konnie from SALEM, OR
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!