GI15NDXTS3 Whirlpool Ice Maker Parts & Repair Help | PartSelect
Models > GI15NDXTS3

GI15NDXTS3 Whirlpool Ice Maker - Overview

Manuals & Care Guides for GI15NDXTS3

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(6)
PartSelect #:PS11730901
Manufacturer #:W10823511
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the or...
$21.65
In Stock
(1)
PartSelect #:PS11742755
Manufacturer #:WP489483
This screw is sold individually.
$8.15
In Stock
(5)
PartSelect #:PS370853
Manufacturer #:4387020
There is approximately 10' of wire. Note: 2 kits are needed to replace both directions.
$40.68
In Stock
(5)
PartSelect #:PS11740331
Manufacturer #:WP2313628
A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down i...
$76.77
In Stock
(7)
PartSelect #:PS11740334
Manufacturer #:WP2313637
If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker and ...
$178.14
In Stock
(10)
PartSelect #:PS11740332
Manufacturer #:WP2313633
This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce ...
$46.16
In Stock
(12)
PartSelect #:PS11738900
Manufacturer #:WP2149705
The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the do...
$23.21
In Stock
(3)
PartSelect #:PS11756166
Manufacturer #:WPW10548509
This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches...
$52.62
In Stock
(4)
PartSelect #:PS11739077
Manufacturer #:WP2185696
This is a drain fastener cap and is used in conjunction with your freezer/refrigerator. This model is almost 1.5 inches in diameter, half an inch thick, and is white in color. This...
$24.38
In Stock
PartSelect #:PS11742733
Manufacturer #:WP489128
This screw is sold individually.
$7.52
In Stock
Questions and Answers for GI15NDXTS3
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken light switch

Door Light Switch – Part Number: WP2149705
  • Customer: Randy from Hays, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 73 of 120 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is alm... read more

was not making ice

  • Customer: Richard from North Wilkesboro, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 40 of 48 people found this instruction helpful
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well read more

Grid Assembly had a broken wire and would not separate the ice sheets into cubes

  • Customer: Brad from Bakersfield, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 31 of 35 people found this instruction helpful
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a... read more