Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GI1500XHB6

GI1500XHB6 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for GI1500XHB6

If you know the ice maker repair part you need, you can browse the list of all parts on the GI1500XHB6, or you can search by name or part description. You can also find your part by where it is located on the GI1500XHB6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$137.02

Ice Cutter Grid Complete Assembly

If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker, and...

$21.01

TUBE-WATER

$91.23

Condenser Fan Motor

NOTE: As per the manufacture the part does not come threaded. A self tapping screw will need to be used to make threads.

$33.58

Ice Cutting Grid Wire

There is approximately 10' of wire. Note: 2 kits are needed to replace both directions.

$17.50

Drain Fastener Cap

This is a drain fastener cap and is used in conjunction with your freezer/refrigerator. This model is almost 1.5 inches in diameter, half an inch thick, and is white in color. This...

$211.19

Circulation Pump with Motor

The circulation pump assembly, used in a free-standing ice maker, delivers water from the water tank over the top of the evaporator plate. It does this to form the ice that drops onto the cutting grid. The first step in installing this part is to remove the chute, ice scoop bracket, water pan, and head cap screw that holds the plastic cover over the pump. Refer to the manufacturer-approved installation instructions for further guidance and accuracy. Make sure to disconnect and unplug the ice maker from the power source before installing the circulation pump. Remember to wear gloves to protect your hands.

$32.86

Tube, Plastic

Used with stand alone ice cube makers.

$5.44

Compression Nut

The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required for this repair include a pair of pliers and a socket set. Before installing this part you should take all perishable foods out of your refrigerator and store them somewhere cool, unplug the refrigerator from the power source, and shut off the water supply. This repair may require you to wear work gloves to protect your hands, and is considered an easy do-it-yourself fix.

$4.37

Screw

Sold individually.

$2.96

Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lack of frequent cleaning resulted in pump failure due to buildup from hard water mineral deposists

  • Customer: Louis from Cheyenne, WY
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 65 of 67 people found this instruction helpful
This ice maker is really a Kitchenaid appliance.

1. Remove all ice and drain water pan by removing drain cap.
2. Disconnect waterline and unplug ice maker
3. Set icemaker on a work bench unless you like working on your knees, head down.
4. Remove flip out chute and ice scoop bracket.
5. Remove water pan by removing thumb sc... read more

Believed the condensor motor was defective and causing strange odor

  • Customer: Nicholas from Frankfort, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 38 of 43 people found this instruction helpful
First disconnected the quick release electrical connection. Then loosened the three screws that were holding the motor in the bracket. However, space is limited and even with small hands it was rather difficult as the screws were in there very tight. There are a few sharp edges on the bracket and in the surrounding area of the motor area, and nicked mysel... read more

Noisy and the Fan wasn't blowing like it should

  • Customer: William from Centreville, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 29 of 30 people found this instruction helpful
I saved my Whirlpool Refrigerator (Model ET21GKXHN00) and learned a lesson. Don’t put off cleaning the refrigerant coils underneath the refrigerator. I replaced the refrigerator about 10 years ago and began to notice that the sound of this one running had changed slightly. I remembered that’s what happened to the first one just before it died. I removed ... read more