This 40w light bulb is a replacement bulb constructed of glass and metal. It is an easy-to-install electrical part which produces 40w of light. If the bulb won't light up then it may be broken and should be replaced. The bulb attaches directly to an appropriate light socket and has a small screw-in base. To access the exterior light bulb,...Read more you will need to remove the panel on the bottom of the microwave using a Phillips screwdriver. If your exterior light bulb has not been changed before, it is probably held in place with some silicone. You will need to cut away this silicone to remove the old bulb. If you cannot access the silicone with a utility knife, it can be removed using dental floss. Once the silicone is removed, simply unscrew the old bulb, and replace it with the new one. Be sure to disconnect the power to the microwave before you begin this repair. This light bulb measures about 1 1/8 inches. We do not recommend using a higher-wattage bulb for this appliance, and can only recommend this specific bulb. If fixing the bulb does not solve your microwave light issue, it's possibly a problem with the socket, which means the socket and/or board will need to be replaced. This can be a more dangerous repair, so consult your user manual or a technician before attempting.
This a genuine OEM microwave cooking tray. It is also known as a microwave turntable or microwave plate. The function of the tray is to hold and rotate food items while the appliance is in use to ensure the food is being heated evenly. This cooking tray is made of transparent glass, and may need to be replaced if the tray is cracked or br...Read moreoken. A broken tray may prevent it from rotating if the three partial circles on the bottom of the tray will not connect to the turntable driver. This part is sold individually and is approximately 12 inches in diameter. It is recommended to check the drive coupling, or turntable driver, if tray is not turning.
This grease filter, used in microwaves, can be located underneath the microwave. The filter traps grease from the exhaust air and removes it from the air stream. This helps prevent grease sticking to the inside of the exhaust hood. Please note that most microwaves require two grease filters and they are both sold separately. This is an ea...Read moresy replacement done by simply pulling out old filters and sliding in the new ones. For further instructions and guidance, refer to the manual provided by the manufacturer. Unplug the microwave from the power source before starting this installation.
This part is plastic with a stainless color finish and comes with the clips needed to mount the grill. The actual stainless steel option is no longer available.
This turntable ring in your microwave makes sure that your glass tray rotates smoothly. Located just above the internal floor, it supports the tray so that your food cooks evenly. A broken turntable ring will look warped or cracked. Additionally, the rotation may become uneven or wobbly. You should replace the ring when it is damaged, by ...Read moresimply taking out the old one from your appliance. Please note that this replacement part is sold individually and is a genuine OEM product, specifically designed for your microwave.
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.
This is an authentic manufactured drive coupling for a microwave. It fits on the motor shaft to hold and rotate the glass turntable tray while the appliance is running. This part has a D-shaped insert for the motor shaft, and measures approximately 3 inches in diameter. You may need to replace this part if the microwave tray will not turn...Read more. No tools are required for this repair. It is recommended to check the support ring before ordering the drive coupling in case the wheels are broken. This part is also known as a turntable coupling or microwave turntable support.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken grill
474 of 476 peoplefound this instruction helpful.
J Richard from Long Beach, MS
Really Easy
Less than 15 mins
Screw drivers
Adjusted clips inserted grill less then two minutes.It took me longer to unwrap the package then it took to install.Ordered part on line 10:45 am delivered 2:30 pm next afternoon.Less then 28 hours later. What service.
Was this helpful?
Thank you for voting!
The grill-vent broke and the grease filters needed to be replaced.
493 of 637 peoplefound this instruction helpful.
M. Rose from Miami, FL
Really Easy
Less than 15 mins
I simply placed the grill-vent in hood area, pulled out the dirty grease filters and slid in the replacement ones.
Purchased new part online. Partselect parts list indicated 3 different part numbers with no other distinction. As a result, I accidentally ordered the wrong color. I had to mail the part back and reorder. Partselect should correct their parts lists to indicate the color of the part. Once I had the right part, installation was sim
... Read moreple.