Models > GFS227

GFS227 (MN00) Caloric Refrigerator - Overview

Sections of the GFS227

[Viewing 12 of 12]
Keep searches simple, eg. "belt" or "pump".
Condenser Fan Motor Kit – Part Number: 833697
Condenser Fan Motor Kit
★★★★★
★★★★★
(34)
PartSelect #: PS395284
Manufacturer #: 833697
This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant ...
$63.18
  In Stock
Door Switch Kit – Part Number: W10169313
Door Switch Kit
★★★★★
★★★★★
(19)
PartSelect #: PS1964648
Manufacturer #: W10169313
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble,...
$29.94
  In Stock
Filter Drier Tube – Part Number: W10843121
Filter Drier Tube
PartSelect #: PS11728084
Manufacturer #: W10843121
This filter dryer is for refrigerators and filters refrigerant that travels through the sealed system of the refrigerator.
$38.13
  In Stock
DISCONTINUED – Part Number: Y0057119
DISCONTINUED
PartSelect #: PS2186610
Manufacturer #: Y0057119
  No Longer Available
Assembly BULK HEAD – Part Number: 60774P
Assembly BULK HEAD
PartSelect #: PS104634
Manufacturer #: 60774P
  No Longer Available
THERMOSTAT,LOW LIMIT – Part Number: 56591
THERMOSTAT,LOW LIMIT
PartSelect #: PS2053583
Manufacturer #: 56591
  No Longer Available
DISCONTINUED – Part Number: 56620
DISCONTINUED
PartSelect #: PS100866
Manufacturer #: 56620
  No Longer Available
DISCONTINUED – Part Number: 57171
DISCONTINUED
PartSelect #: PS379573
Manufacturer #: 57171
  No Longer Available
DISCONTINUED – Part Number: 502804
DISCONTINUED
PartSelect #: PS93592
Manufacturer #: 502804
  No Longer Available
THERMOSTAT,COOL-DOWN – Part Number: 56590
THERMOSTAT,COOL-DOWN
PartSelect #: PS100856
Manufacturer #: 56590
  No Longer Available
SUB 61376P – Part Number: 57024
SUB 61376P
PartSelect #: PS101684
Manufacturer #: 57024
  No Longer Available
SUB 61376P – Part Number: 57025
SUB 61376P
PartSelect #: PS101690
Manufacturer #: 57025
  No Longer Available

Questions And Answers for GFS227

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the GFS227

[Viewing 9 of 9]
Fridge too warm
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing Fixing
Show All
Freezer section too warm
Fixed by
these parts
Fixing
Show All
Fridge runs too long
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Show All
Fridge and Freezer are too warm
Fixed by
these parts
Fixing
Show All
Won’t Start
Fixed by
these parts
Fixing
Show All
Too warm
Fixed by
these parts
Fixing
Show All
Leaking
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sometimes the condenser fan would start causing the refrigerator to overheat.
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new
Parts Used:
Condenser Fan Motor Kit
  • Tom from Franklin, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
180 of 204 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch sticking in on position
FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two screws holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom.
Parts Used:
Door Switch Kit
  • Don from Jacksonville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
99 of 133 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
noisy fan motor
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.
Parts Used:
Condenser Fan Motor Kit
  • robert from nashotah, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
37 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!