GFS208 Caloric Refrigerator Parts & Repair Help | PartSelect
Models > GFS208
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(72)
PartSelect #:PS2121513
Manufacturer #:D7824706Q
This is a replacement ice maker. This assembly includes the ice mold and the control device. The water inlet valve pumps water into the mold, which stays there until it is frozen s...
$88.90
In Stock
(38)
PartSelect #:PS884734
Manufacturer #:8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...
$6.12
In Stock
(16)
PartSelect #:PS395284
Manufacturer #:833697
This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling t...
$51.30
In Stock
(8)
PartSelect #:PS11743318
Manufacturer #:WP628356
This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ic...
$20.63
In Stock
(9)
PartSelect #:PS376645
Manufacturer #:482731
The evaporator is found in the back of the freezer. This kit comes with two mounting grommets, two sleeves (not to be used on porcelain models), two #8 mounting screws, and a push-...
$70.60
In Stock
(1)
PartSelect #:PS11743313
Manufacturer #:WP627985
The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine wh...
$33.87
In Stock
(11)
PartSelect #:PS11738900
Manufacturer #:WP2149705
The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the do...
$19.67
In Stock
(3)
PartSelect #:PS328693
Manufacturer #:2188450A
This white fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.
$93.65
In Stock
PartSelect #:PS11742733
Manufacturer #:WP489128
This screw is sold individually.
$6.98
In Stock
PartSelect #:PS11742859
Manufacturer #:WP57005
Felt pad sold separately.
$22.58
In Stock
Questions and Answers for GFS208
Be the first to ask our experts a question about this model!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

Replacement Ice Maker – Part Number: D7824706Q
  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 763 of 815 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

Replacement Ice Maker – Part Number: D7824706Q
  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 261 of 339 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 154 of 166 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more