This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appliance to both start and complete a full drying cycle. There are two pieces included in this kit, one catch, and one strike. You open and clos...Read moree the door on such a regular basis that this mechanism can wear out. It is a fairly common part to replace. You will need to remove the door of your dryer to install the replacement catch assembly.
This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 V...Read moreolt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.
This refrigerator kick plate grill is sold individually. Order two if you need to replace both clips. *Please note, if you are ordering the kick plate, check with your model number as these parts may be included.
The kickplate grille attaches across the bottom of the refrigerator and allows air to flow into the machine compartment to cool the condenser. The main reason to replace your grille is because it has become damaged, or will not fasten properly due to a broken mounting clip. This grille is black in color, made completely of plastic, and me...Read moreasures approximately 33 inches long x 5 inches wide. This is a genuine OEM replacement part, and fits many different brands and models. Be sure to check if this part will fit your model before purchasing. This kickplate grille comes with mounting clips.
If your ice maker is not producing ice, it could be due to a faulty, damaged, or broken drive gear. The ice maker drive gear attaches to the cam to turn the ice cube tray. Check the alignment of the drive gear and make sure the teeth are not stripped or broken. Also, check and clear anything that could be stopping the gear from turning pr...Read moreoperly. If there is damage to the gear it should be replaced. Before you start this repair, remember to disconnect the water and power to your unit.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sometimes the condenser fan would start causing the refrigerator to overheat.
184 of 223 peoplefound this instruction helpful.
Tom from Franklin, WI
A Bit Difficult
15 - 30 mins
Nutdriver, Pliers
Unplug the appliance. Removed the screws holding the back panel. Removed the fan blade. removed 3 screws holding the condenser fan. Remove the 3 metal brackets attached to the fan. (First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied) Cut
... Read moreand strip the wire about two inches from the fan. Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws) Screw the back panel back on. Mount the new
Read less
Was this helpful?
Thank you for voting!
catch mounted on door broke
94 of 127 peoplefound this instruction helpful.
Paul from Mt. Pleasant, SC
Really Easy
Less than 15 mins
Screw drivers
The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.
Was this helpful?
Thank you for voting!
noisy fan motor
38 of 46 peoplefound this instruction helpful.
robert from nashotah, WI
A Bit Difficult
30 - 60 mins
Nutdriver, Socket set
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, c
... Read morelose up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.