The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse ...
This part replaces your appliances latch (Door Latch Kit, Door Catch, Dryer Door Latch Kit). On your appliance you will find both a strike and a catch. The strike is mounted on the body of the dryer, ...
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside ...
The filter collects lint during the drying cycle. This filter is 12 1/2 inches wide and 10 1/2 inches deep. Replacing the lint filter is an easy repair which requires no tools. When replacing the lint...
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings,...
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium"...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
$11.40
In Stock
Questions And Answers for GEW9200LW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Debbie
March 25, 2020
Under the status column , the last bullet point says control locked....? how do i unlock it, pushed many buttons, unplugged nothing seems 2 work it won't start help!
For model number GEW9200LW1
Hi Debbie,
Thank you for your question. To unlock your dryer, press and hold the "End of Cycle Signal Button" for 3 seconds. For more information on how your dryer operates, here is a link from our website where you may view your owner's manual, https://partselectcom.azureedge.net/assets/manuals/2B9FA31D1270709ED6946B3B631F2480E0D86BDA.pdf. We hope this helps. Thank you and have a great day.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
May 16, 2023
Dryer would not spin ... made a humming noise. Removed the motor and it is very difficult to spin by hand. Can spin the motor with leverage from a wrench, but it does not feel smooth. Does this mean the motor is defective?
For model number GEW9200LW1
Hi Jim, thank you for reaching out. Based on our understanding of the issue, we would suggest you replace the drive motor, part number PS334287, as it is most likely faulty. We hope this helps!
When i push the on button it'll make a clicking sound and it won't start.. when i change it to different cycles everything goes right the right lights come on but it still makes the clicking sound and won't start...
For model number GEW9200LW1
Hi Pamula,
Thank you for your question. If your dryer is not starting on one cycle, there are some parts that you will need to check to see which one is causing the issue. You will need to check the thermal fuse, the door switch, the electronic control board, the hook and strike, the high limit thermostat and the thermal cut off and the internal bias thermostat. We hope this helps! Good luck with the repair!
Hi Barbara. We are not whirlpool however. I would test your thermostats, check for clogged vents as this may cause the dryer to be too warm. Thank you for your question and good luck with your repair.
For model number GEW9200LW1
Hi Barbara. We are not whirlpool however. I would test your thermostats, check for clogged vents as this may cause the dryer to be too warm. Thank you for your question and good luck with your repair.
Is it possible to change the direction the door opens?
For model number GEW9200LW1
Hello Michael, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS973431 for the Door Reversal Kit in Platinum and PartSelect Number PS973433 for the Door Reversal Kit in Pewter. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils. Not knowing what the problem was I started looking at the coils and could not see any broken parts. So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of
... Read moreneedle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading. I replaced with a new one and put it all back together the way I took it apart. Then I plugged it in and it worked first time, I now have warm dry clothes.
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.
Ascertaining the problem was the most time consuming part.
The actual repair was quite simple and did
... Read moren't take but 15-20 minutes.
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.