GCV160LAR3A Honda Engine - Overview

This air cleaner element, also known as an air filter, is found in your lawn equipment. Typically housed in a rectangular container, it is located near the air intake area or carburetor of your machine. It keeps dust, dirt, and debris from entering the combustion chamber. If it is clogged, the restricted airflow will make the engine misfi...Read morere or run poorly, and potentially cause an engine failure. To replace the element, you will need to remove its housing cover by unscrewing or unclipping it. This OEM-certified filter is sold individually.

This is a genuine component which is specially designed for use with Honda engines commonly installed on lawn and garden equipment. It is supplied directly from the original equipment manufacturer. This bolt-stud helps to mount the cover-fan and the pull-starter. Please make sure to refer to the appropriate diagrams of your model for the ...Read morecorrect application of this hardware. Keep in mind this high-quality bolt-stud is made of durable metal and is sold individually. Replacing it is a simple task that should only require a wrench set to remove the old and secure the new.

Genuine Honda Engine replacement part, this item is sold individually. This part covers and secures the Air Cleaner Element to the Air Cleaner Case Assembly on the engine. It also has ports in it to allow air into the engine so it will perform properly.

This is a genuine Honda replacement part, it is sold individually. The Honda Insulator Gasket is installed between the Cylinder housing and the Carburetor Insulator ( Or Heat Dam). Its purpose is to create a seal so that air cannot enter the cylinder causing the engine to operate poorly. It also keeps other debris from entering the engine...Read more and damaging it. If this part becomes cracked or worn it should be replaced ASAP.

Genuine OEM replacement part, this item is sold individually. The purpose of this Gasket is to create a seal between the air cleaner body and the carburetor. If the air cleaner or carburetor are ever removed, it would be a good idea to replace this gasket.

Genuine Honda replacement part, this part is sold individually. The Insulator- Carburetor acts as a insulator to keep heat from transferring from the engine to the carburetor, which could cause damage to the carburetor.

This genuine item is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. It is the main cover for the cylinder assembly. The part helps to protect the internal components from dust and other contaminants. If your cover is damaged or is missing,...Read more this will provide an identical replacement for the original component that was installed on a new unit. This high-quality head cover is made of durable metal and is sold individually. Note, the hardware to secure it is sold separately. You will need a wrench to perform this repair.

This genuine OEM sourced replacement part designed for use with lawn and garden equipment engines. The purpose of a carburetor is to mix air and gas before the fuel mix goes to the engine. If the engine won\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel int...Read moreo the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This governor spring regulates the engine speed in your lawn equipment. It works in conjunction with the governor mechanism to control the throttle and prevent the engine from over-revving or running at an excessively low speed. It is commonly found near the throttle assembly. Keep an eye out for signs of wear, damage, or stretching in th...Read moree spring. If it appears weak, worn, or if you notice engine surging or difficulty maintaining a steady speed, it may indicate a broken governor spring. Before replacing the spring, ensure the engine has cooled down. Remove the wire and boot from the spark plug and turn off the fuel valve. To replace the governor spring, unhook both ends of the old spring while taking note of the connection points. Install the new spring by hooking one end onto the governor lever and the other end onto the control bracket assembly. Once securely attached, turn the fuel valve back on and reattach the spark plug wire and boot. This replacement part is sourced directly from its original equipment manufacturer.

This item is an authentic Honda replacement part and has been sourced from the original manufacturer to be used with small engines. The seal is used to prevent oil from leaking from between the crankcase and the crankshaft. The oil seal is available as an individual replacement part.