GC2126C (2008-06) Jonsered Trimmer - Overview

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

The air filter prevents dirt and debris from entering the engine on your lawn equipment. This is an OEM filter that is white, roughly 2x3.5 inches in dimension, and can only be purchased individually. Made of foam, the air filter becomes clogged and worn over time, causing the engine to run rough from restricted air flow. You can make t...Read morehis repair easily with no required tools by inserting the new filter inside the air cleaner housing of your engine.

This is an OEM part guaranteed to fit Milwaukee power tools. This trigger spring is attached to main trigger. Please note that only trigger spring is included. When disassembling this area, be sure to slowly separate parts in order to prevent springs from being lost when released too quickly. Though they appear similar, a lockout spring i...Read mores a different part used with the throttle lockout (not present in all models). This part is often purchased with: • Trigger, part # 545066001 • Throttle Lockout, part # 530059804 • Lockout Spring, part # 545045601

This purge bulb is an authentic OEM part from Craftsman for gas blowers, trimmers, blowers and weed wackers. This part disperses fuel to the carburetor to provide starting the blower faster. You will need a screw driver to replace this part. This purge bulb is made of rubber and sold individually.

This is an authentic OEM sourced replacement part designed for use with handheld lawn and garden equipment. This is a standard hardware which has multiple applications depending on the equipment. Please make sure to check appropriate diagrams for correct location and use of this item. One hex socket head screw is included per order.

This is an authentic replacement part supplied from Poulan. It is generally used with gas powered chainsaws. This nut in conjunction with a bolt (sold separately) helps to secure air filter and carburetor. Requires a wrench installing/removing this item. It is sold individually.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.

This genuine manufacturer sourced replacement part is specially made for use with a variety of handheld lawn and garden equipment. This part is installed on top of the piston/connecting rod. Its purpose is to create a seal in the cylinder so that it can build pressure. A worn or broken piston ring will allow combustion gases to escape the...Read more seal and enter the crankcase, causing low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. Includes one (1) metal piston ring. Tools Required: Receptacle for draining fuel, Torx wrenches, spark plug wrench, 10mm wrench (or adjustable), long-nosed pliers, rubber mallet, standard screwdriver, old starter rope (or similar cord), adjustable pliers, 2-cycle engine oil, razor blade, ignition gapping gauge. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring

This is a genuine OEM sourced replacement part designed for use with Poulan and Husqvarna handheld lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please make sure to check appropriate diagrams for correct location and use of this item. Please note, one torx screw is included per order.

This is an authentic OEM sourced replacement screw which is produced for use with Husqvarna handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. Note this special Torx screw is sold individually.

This is an authentic OEM sourced replacement part that is intended to be used with trimmers, brushcutters, and edgers from Husqvarna and Jonsered. The metal nut is used with several different types of machines and the application of the nut can vary based on the model of the equipment. This nut is sold individually.

This item has been OEM sourced to ensure a high level of quality. The gearbox assembly is intended to be used with trimmers from Husqvarna and Jonsered. The gearbox attaches to the bottom of the lower drive shaft. This item is used to connect the rotation of the shaft with the rotation of the cutting head. This gearbox is sold as an individual replacement part.