GC145 (2010) Cub Cadet Tiller - Overview

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This foam air filter in your lawn equipment serves as a protective barrier, preventing dirt, dust, and debris from entering the combustion chamber. Clean air is crucial for efficient fuel combustion. Typically located in the air intake system, a dirty, damaged, or torn air filter indicates the need for replacement. If you have trouble sta...Read morerting, reduced power, or rough operation, it may be due to a compromised air filter. To replace the air filter, unscrew the knob on the housing cover, swing it out, and remove the old filter. Consult the user guide for installation instructions. Before adding this to your cart, please be aware that this OEM replacement part is sold individually.

This is a genuine replacement part from original manufacturer. It is compatible with Ryobi, MTD, Troy-Bilt, Yard Man, and Bolens machines. It\\\'s used with a variety of power tools including trimmers, tillers, and blowers. O-rings create a seal between solid parts, retaining pressure. Because many machines use more than one type of O-rin...Read moreg, use care to ensure that the right one is being used in the right spot. This ring is sold individually.

This genuine OEM supplied part is specially designed for use with a variety of lawn and garden equipment. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this part. This is an identical replacement for ...Read morea missing or a damaged flange lock nut that was installed on a new equipment. One durable metal part is included. A wrench will be needed to secure or remove this hardware.

The Clutch Drum is a silver, metal part used to transmit power from the engine to the drive shaft. Installation is rated "Medium" difficult and will require a screwdriver, wrench set, and torx wrenches. This part attaches to the clutch assembly. If broken, the clutch will slip and you will lose drive power. If this happens, the part must be replaced.

This is a genuine item that is supplied by the original equipment manufacturer for use with trimmers. The metal clutch goes between the clutch drum and the clutch washer. It helps to spin the cutting head and the flex shaft. It may require a screwdriver and a hammer for installation. This clutch is available as an individual replacement part and comes with a washer.

This is an Genuine OEM replacement part used on Gas-Powered Handheld Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull th...Read moree starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor with Rubber Primer Bulb and Two (2) Rubber Fuel Lines. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.

The Push Cap Rod is a 1/2-inch metal metal cap which can be easily installed with a hammer and pliers. This manufacturer certified part comes in silver and is made of metal. This cap attaches onto an axle to help the wheel stay attached. If broken, the wheel will fall off and the part should be replaced.

This is a genuine replacement part sourced from the original manufacturer for use with tillers. The special gear box assembly is used to drive the tiller's tines and includes the axle and gears. This gear box assembly is available as an individual replacement part, please see model diagram for associative parts.

This tiller tine assembly is designed to dig into and break up soil, grass, and compacted ground on forward-rotating cultivators. Built from durable steel with an L-shaped profile, it helps turn and loosen soil efficiently for planting and garden preparation. Ideal for replacing a bent or worn tine, it restores proper tilling performance and smooth, consistent operation during regular use.

This is an authentic OEM MTD, Ryobi, Troy-Bilt, Yard-Man, Bolens, Yard Machines part for use with line trimmers. The engine flywheel attaches to the crankshaft behind the recoil starter assembly. The recoil starter engages the flywheel to spin and start the engine. The most common use for replacing the flywheel assembly is if the engine ...Read moreis misfiring, missing, stuttering not starting or overheating. This part is sold individually. Here is a list of tools that are needed to replace the engine flywheel a receptacle for draining fuel, Phillip's screwdriver, Torx wrenches, starter rope (or similar object) for binding the engine, spark plug wrench or socket, adjustable wrench, long-nosed pliers and a rubber mallet. Let the engine cool and disconnect the spark plug wire before installing this part.