G3050OH (G 3050 OH 11945150) Karcher Pressure Washer - Overview

Genuine Karcher replacement part, this item is sold individually. The purpose of this part, is to attach the Female Hose Connector to the Piston Guide. This part is made of plastic and has plastic threads that do wear out. It may be wise to have an extra one or two on hand.

This OEM Grooved Ring is a 12 x 20 x 4/6 rubber ring which can be installed with a screwdriver and wrench set. Installation is rated as "Medium" difficulty. It attaches in the cylinder head and is used to keep the oil in the pump from mixing with the water. If broken it will leak and must be replaced.

Genuine Karcher replacement part, this item is sold individually. This O-Ring/ Seal is part of the water inlet system of the Pressure Washes shown below. Over time this type of part will deteriorate and fail. At this time you will notice a water leak and need to replace this part.

This high quality wheel and tire assembly is a genuine manufacturer sourced replacement part that is specially produced for Karcher pressure washers. It is the wheel that supports and helps to move your unit around. This part consists of a durable metal wheel with a rubber tire and it is sold individually, please note the hardware to secure it is sold separately.

This is a genuine item that is specially designed for use with Karcher pressure washers. It is supplied by the original equipment manufacturer. The oil helps to lubricate internal components of the pump to ensure it runs properly. Check the oil level regularly. Oil level should always be between the "FULL" and "ADD" level marks on the dip...Read morestick. Be sure the machine is level when checking the oil level. This will prevent them from wearing out. Refer to the owners manual of your model for the correct application of this oil. This synthetic 15W40 oil is sold in a single 1-liter container.

This is a Genuine Manufacturer Sourced replacement part used on Karcher Pressure Washers. This item is made out of Metal and it is Sold Individually. This Female Garden Hose Connector in conjunction with Male Adapter is used to attach Garden Hose to Pressure Washers Pump. Requires a Wrench to secure.

This part is a Retrofit Valve that will work on the older models as well as the newer models. Older units have shorter valves than the new pumps but you can change the length of the stem to adjust for the older units.

This rubber buffer is an authentic OEM component which is designed for use with Karcher pressure washers. It is attached to the bottom of the frame in order to provide support for the unit. Over time it may wear out, get damaged or lost eventually requiring a replacement. Make sure to refer to the diagrams of your model for the exact loca...Read moretion and the correct installation. One durable rubber buffer is included. Note, the bolt that secures this component is sold separately. Replacing this buffer is a simple task that should not require any tools. If your old part does not unscrew, you may use pliers to remove it.

This is a genuine OEM sourced replacement part designed for use with Karcher pressure washers. This high pressure hose is made out of rubber/plastic material. It is 25 ft long and it is sold individually. This hose can be used on pumps that produce up to 3600 PSI. Easily connects to the washers with M22 connection.

Genuine Karcher replacement part, this item is sold individually. The purpose of the 9.181-005.0 Filter Seal Hose Connector is to act as a seal to keep water from leaking out of the hose connection. It also will keep debris from entering the pump and causing it to fail.

This item is a genuine Karcher replacement part that has been sourced from the original manufacturer and is intended to be used with pressure washers. The durable plastic know is used as a wingnut that fastens the bolt that secures the two halves of the handle tubes. This knob may not require tools to install and is sold as an individual replacement part.

This is an authentic Karcher replacement part that has been sourced from the original manufacturer to be used with pressure washers. The metal cap is used to cover the end of the axle that the wheel mounts to. This cap is available as an individual replacement part.