FS6300 (Type 2) Makita Screwdriver - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes...Read more can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine Makita replacement part, it is sold individually. It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers. Compatible with the tools listed below. The diameter is 3.5mm.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This is an authentic OEM sourced part which is specially made for use with Makita power tools. It is an identical replacement for a missing or a faulty steel ball that was installed on a new unit. This is a standard hardware which may have multiple applications, please make sure to check the appropriate diagrams of your model for the corr...Read moreect location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This cord protector is an OEM part designed for a variety of Makita power tools. It is attached where the power cord meets the tool. This part protects the cord from damage due to pulling, bending, or other strain. This rubber cord protector is sold individually. It does not include a replacement cord.

This genuine OEM supplied part is specially designed for Makita screwdrivers. The depth can be adjusted by turning the lock ring. Turn it in

Included in part number 515616-3

This is an authentic OEM approved replacement armature assembly which is designed for use with Makita drywall screwdrivers. The armature is the central component of an electric motor, due to constant contact with carbon brushes armature will eventually wear out and would need to be replaced. It is highly recommended to replace both carbon...Read more brushes when replacing an armature. This complete assembly is sold individually, it includes the armature, the plastic fan, the armature bearing and the commutator end bearing.