Water for the refrigerators water and ice system passes through this OEM filter, which connects with a push-to-lock fitting. Check the refrigerators model number before ordering to confirm compatibility. Its rated capacity is 125 gallons, with a flow rate of 0.65 gallons per minute.
A refrigerator or freezer door handle is held in place by this screw. The OEM part has a #10-16 thread, a 1/2-inch length, and a Phillips/Square drive. Confirm it matches your appliance before ordering.
This metal shoulder screw secures a refrigerator or freezer door handle to the outer door panel. It is a number 10 AB handle mounting screw and is sold individually. A missing screw, damaged threads, or a worn screw head may leave the handle loose or prevent it from attaching securely. Check the handle and mounting point for damage before...Read more replacing the screw, since either can also cause movement. Confirm the correct fastening location in the appliance parts diagram before installation. This is an OEM part sourced directly from the manufacturer.
This temperature sensor, also known as a thermistor, is responsible for preventing the evaporator within your refrigerator from overheating during its defrosting cycle. This sensor is compatible with various makes and models of refrigerator and is sold as an individual part. This sensor works with the electronic control board within your ...Read morerefrigerator to control the temperature by turning the compressor on or off. If your fridge is too warm or too cold, consider changing the thermistor with this genuine OEM part, and make sure to disconnect the power to the refrigerator before doing any repairs.
Warm air entering around the fresh food door can affect cooling. This gray magnetic gasket seals the refrigerator door to help block that air. Check the refrigerator model before ordering. Before installation, warm the gasket in warm water or with a hairdryer on low heat. It is an OEM part.
Refrigerator interior lighting uses a warm-white, 120-volt LED bulb with an E17 base. This bulb is listed for top-mount refrigerators and upright freezers. Check your appliance model to confirm fit. It is an OEM part.
Store gallon containers on the refrigerator door with this clear plastic bin assembly. It is an OEM part listed for select refrigerator models, so check your refrigerator model for compatibility.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My fridge temp was warm. Freezer temp was ok, but fluctuated some.
58 of 92 peoplefound this instruction helpful.
Cindy from AMARILLO, TX
Really Easy
Less than 15 mins
Screw drivers
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used
... Read more my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Read less
Was this helpful?
Thank you for voting!
Gasket/seal was worn/broken on bottom edge.
18 of 22 peoplefound this instruction helpful.
suzanne from vermilion, OH
Really Easy
Less than 15 mins
Pulled the old gasket off and put new gasket/seal on by pressing firmly into slot.
Was this helpful?
Thank you for voting!
I had a light come on and tell me I needed a new water filter
18 of 27 peoplefound this instruction helpful.
Marlene from SCOTTSDALE, AZ
Really Easy
Less than 15 mins
Pushed the old filter in and it came out then I pushed in the new one.