FRC800K1 (Type AVIN# GCBKT-1000001-9999999) Honda Tiller - Overview

This is a genuine Honda replacement spark plug. It is sourced directly from original equipment manufacturer and it is sold individually. It is designed to ignite the air fuel mixture by the spark. If spark plugs are not checked with regular services, cleaned or changed when necessary, they can cause problems to occur with the engine. Replacing it you should only need a spark plug socket.

This spark plug creates the spark needed to start compatible small gas engines, it is used in select lawn mowers, generators, snow blowers, and pressure washers, replace a worn or dirty plug if the engine is hard to start, runs rough, or loses power, let the engine cool and remove the plug wire before repair, use the exact engine model number to confirm fit.

This metal washer is compatible with several different makes and types of small engine equipment, and is a genuine OEM part. Used to evenly distribute pressure on the oil drain from the drain bolt, this washer has a 19mm/.75-inch outer-diameter and 12mm/.5-inch inner-diameter and is sold individually without the drain bolt, which is sold ...Read moreseparately. It is, however, recommended that if you replace this washer, you replace the drain bolt as well.

This is a genuine replacement part which is supplied by the original equipment manufacturer. It is specially designed for use with Honda engines commonly installed on a variety of lawn and garden equipment. The purpose of it is to filter out dirt and other debris from the fuel that is supplied to the engine. It will over time become clogg...Read moreed and restrict the fuel from getting to the carburetor so it will need to be replaced. It is made of a high-quality plastic and is sold individually. Check the diagrams of your model for the correct installation of the new part.

This genuine OEM oil filler cap assembly is part of your lawn equipment, found commonly on the top or side of the engine. It covers the oil fill hole on the engine so that oil does not spill out and impurities do not get in. A broken cap may be visibly damaged and will not properly seal the oil fill hole. If you do not replace it, the oil...Read more may become contaminated with dirt, reducing the lifespan of your engine. To remove the cap from your machine, gently grip onto it and rotate it counterclockwise. You can lift the cap straight up afterwards. This part is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This rubber fuel strainer cup gasket, found in your garden equipment, distributes pressure and creates a seal between the fuel strainer cup and the carburetor so that fuel does not leak. If it is broken, you will notice fuel leakage or a gas smell, and your engine may sputter or have difficulty starting. Unattended fuel leaks not only was...Read morete fuel but also pose a fire hazard. When removing the gasket, make sure that your machine is shut off and has cooled down. Consult your instruction manual to locate the fuel strainer cup, remove mounting screws and clips with a screwdriver, twist the cup slightly, and lift it away. Peel off the old gasket carefully. It is important to be aware that this authentic OEM replacement part is sold individually.

This item is an authentic OEM part which is made for use with Honda engines commonly installed on a variety of lawn and garden equipment. The clip is utilized to secure the fuel tube. If the clip is damaged or is missing, this will provide an identical replacement for a missing or a damaged component that was installed on a new unit. Chec...Read morek the diagrams of your model for the exact location and the correct application of this hardware. One durable metal clip is included. You may need pliers to secure and remove it.

This rotary tiller tine is designed for rear-tine rototillers to deliver effective soil cultivation and consistent digging performance. Manufactured from durable metal for long service life, it mounts precisely to maintain proper tine rotation and balance during operation. It’s a practical replacement for restoring tiller efficiency and ensuring even, reliable soil breakup when an existing tine is worn or damaged.