FMD60 Exmark Lawn Mower - Overview

This is a replacement screw, also known as a shear pin that is used in several pieces of outdoor power equipment. It is made of metal and is approximately 2 inches in length. It is a hex head screw and is sold individually. This is an OEM part sourced directly from the manufacturer.

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This oil seal is a genuine OEM replacement part designed for lawn and garden equipment. It is a small, circular rubber seal with a diameter of 2 3/8 inches, used to prevent oil leakage between the gear cover and gear shaft, and prevent the entry of contaminants. You will need to replace this oil seal if it is brittle, cracked, or has lost...Read more elasticity. A faulty seal will cause the gears to lose lubrication, increase friction damage, and prematurely wear down the parts. Remember to drain the oil from your equipment before beginning any repairs. Carefully pry the old seal from its mounting position and clear off any debris and residue on the area. Place the new seal in position and ensure it is securely fitted.

Made of durable black rubber, this Oil Seal is an authentic OEM part for use in over 150 models of small engines. This part is sold individually, not as part of a kit or assembly. It will be found on the crankcase opening, where the crankshaft is. The Seal should be replaced when it becomes worn or damaged. When it malfunctions, you'll s...Read moreee oil visibly leaking. To complete this repair, you will need a screwdriver, pliers, a socket set, a wrench set, a nut driver, and an impact wrench. Customers rated the difficulty of this repair as Expert.

This Spark Plug is a genuine OEM sourced replacement part for various small engines. It is white and silver, made of metal and ceramic components, and sold individually. The Spark Plug ignites the air-fuel mixture inside the combustion chamber. Before replacing, you can attempt to clean the spark plug with fine sandpaper of around 180 g...Read morerit, followed by spraying it with carburetor cleaner and wiping it dry. If this does not resolve your issue, it will need to be replaced. Ensure you gap and torque it to the manufacturer specifications. To complete this repair, you will need a spark plug socket, a socket set, and a torque wrench. Customers rate this repair as Easy.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

The flat washer is an OEM replacement part that provides a wide surface area to distribute the load of a bolt or a screw when it is installed. This protects the part being fastened from getting damaged or deformed and provides a more secure fit for the bolt/screw. This flat washer is made of steel and has a diameter of 0.375 inches and a ...Read morethickness of approximately 0.063 inches. To replace the flat washer, first unthread the bolt/screw before using a flathead screwdriver to carefully pry it off. Clean the area, place the new flat washer in position, and thread the bolt/screw back on. Sold individually.

This is an authentic replacement part manufactured for use with Toro snowthrowers. The ni lock nut is designed to prevent from being unthreaded from vibration. This nut is used with several different models of snowthrowers and is used with various applications. The nut is sold as an individual replacement part, please see model diagram for associative parts.

It is a genuine OEM sourced replacement part which is specially designed for use with Toro snowblowers. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.