FL3520 Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This is an authentic part that is supplied directly from the original equipment manufacturer for use with Craftsman Air Compressors. The exhaust flapper valve attaches on the valve plate under the cylinder head. The most common reasons for replacing the flapper valve is if there is poor performance, or the air leaks out of the intake air ...Read morefilter while the unit is running, damaged/sticking valves is a common issue when you have low compression, and can also cause the motor/engine to stall and too much pressure in the pump's crankcase. This part is sold individually. Here is a list of tools that are needed to install the flapper valve are a screwdriver, socket wrench, and a wrench.

This replacement flapper valve is a high quality item that is sourced from original equipment manufacturer for use with Campbell Hausfeld air compressors. This part is secured under the cylinder head helping to control the fuel-air mixture admitted to the cylinder. As the piston rises in the cylinder a vacuum is created in the crankcase b...Read moreeneath the piston. This part is made from durable metal and it is sold individually.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

Sourced directly from the manufacturer, this plug is an exact replacement part for a variety of air compressors. This part is sold individually, not as part of a kit or assembly. It is gold, made of metal, and will be found on the pressure switch. This part will leak when it has become defective and will need to be replaced if it is dam...Read moreaged or worn. When you install the part, apply Teflon tape to the threads before tightening it in place. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This handle is an original replacement part supplied by the manufacturer. It is commonly used in Campbell Hausfeld air compressors. It is compatible with over 150 models. This handle is attached to the top of the tank (part AR040500CG). A screwdriver is needed to remove and replace the screws that secure this part.

This part is an OEM from Campbell Hausfeld. The axle bolt is compatible with many air compressors, and is sold individually. The metal bolt fastens the wheel to the base of the tank, providing movement to the device. A wrench and pliers are needed for the removal and replacement.

This is an authentic replacement part sourced directly from the manufacturer. The wheel is commonly found in Campbell Hausfeld air compressors. This part is made of high-quality plastic and rubber, and is placed on the sides of the tank to make the machine easier to relocate. You will require a wrench when replacing this item. The wheel is provided as an individual replacement part.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

This is an OEM part sourced directly from the manufacturer. The screw is commonly found in Craftsman compressors and paint sprayers. This part is made of metal, and is generally used to secure the flapper valves in the cylinder head. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be ...Read moresure of ordering the correct part. You will require a screwdriver when replacing this item. The screw is provided as an individual replacement part.