EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

FH3F4CDYP1 LG Washer - Overview

Diagrams for FH3F4CDYP1

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine Drain Pump – Part Number: 4681EA2001T
$58.42
In Stock
Washing Machine Drain Pump
★★★★★
★★★★★
(315)
Part #4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$35.80
In Stock
Water Inlet Valve - Hot
★★★★★
★★★★★
(94)
Part #5220FR2006H
The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.
Water Inlet Valve - Cold – Part Number: 5220FR2075L
$139.65
Special Order
Water Inlet Valve - Cold
★★★★★
★★★★★
(93)
Part #5220FR2075L
The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and 2 water outlets facing 45 degrees to the left. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 4 inches long x 3 inches wide.
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
$55.29
In Stock
Tub-to-Pump Drain Hose
★★★★★
★★★★★
(16)
Part #4738ER1002A
This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. Be sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.
Detergent Dispenser – Part Number: 3891ER2003A
$24.67
In Stock
Detergent Dispenser
★★★★★
★★★★★
(20)
Part #3891ER2003A
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is broken, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is made of blue plastic, and is approximately 4 inches wide, 4.5 inches long, and two inches tall. This is an OEM part made by the manufacturer.
Washer Hose with Bellows – Part Number: 4738ER1004B
$42.12
In Stock
Washer Hose with Bellows
★★★★★
★★★★★
(12)
Part #4738ER1004B
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.
Door Boot Seal – Part Number: MDS47123602
$104.33
In Stock
Door Boot Seal
★★★★★
★★★★★
(10)
Part #MDS47123602
Made from high-quality rubber, this washer door boot gasket creates a watertight seal between the door and tub to prevent leaks. It’s compatible with many LG and Kenmore front-load washers and replaces several older part numbers. A reliable fix for water leakage and odor issues.
Hose – Part Number: 4738ER2002A
$47.40
In Stock
Pressure Switch Assembly – Part Number: 6601ER1006E
$72.00
In Stock
Heater Assembly – Part Number: AEG33121501
$125.62
Special Order
Heater Assembly
★★★★★
★★★★★
(4)
Part #AEG33121501
This heating element assembly warms water during wash cycles to improve cleaning performance. It's designed to deliver steady, consistent heat so your laundry comes out fresh and thoroughly cleaned.
HINGE ASSEMBLY – Part Number: AEH71610402
No Longer Available
HINGE ASSEMBLY
Part #AEH71610402

Common Symptoms of the FH3F4CDYP1

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing maching wouldn't drain
592 of 761 people found this instruction helpful.
  • Jorge from Apple Valley, CA
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Was this helpful?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
60 of 81 people found this instruction helpful.
  • Michael from RALEIGH, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this helpful?
Thank you for voting!
leaking tub-to-pump drain hose
52 of 76 people found this instruction helpful.
  • Leslie from STOWE, VT
  • Easy
  • 30 - 60 mins
  • Screw drivers
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this helpful?
Thank you for voting!