FGX831FS3 Frigidaire Washer Dryer Combo - Overview

Diagrams for FGX831FS3

See every part. Know exactly what you need.

Parts for the FGX831FS3

$43.77

Rear Drum Bearing Kit

★★★★★

(114)

Part #5303281153

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if it is making a lot of noise, it could be an issue with this part. This is a ball-and-socket style bearing. You will need to replace this if t...Read more

Read less

$10.93

Drum Support Bearing

★★★★★

(21)

Part #131825900

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although rep...Read more

Read less

$41.75

Drum Glide - White

★★★★★

(17)

Part #137513300

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each ...Read more

Read less

$24.41

Drive V-Belt

★★★★★

(31)

Part #134511600

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; ch...Read more

Read less

$62.37

Door Catch

★★★★★

(31)

Part #131658800

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this instal...Read more

Read less

$54.95

Dryer Lint Screen

★★★★★

(28)

Part #5304516871

This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.

$24.15

Thermal Limiter - Limit 220

★★★★★

(13)

Part #134120900

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts out. If the thermal fuse is defective, damaged, or blown up then the dryer wont start, especially since it cannot be reset. It must be replace...Read more

Read less

$12.05

Multi-Rib Drum Belt

★★★★★

(14)

Part #137292700

The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Over time this part will naturally dry out. If your drum belt begins to crack or break, the dryer will not be able to continue to turn. If your...Read more

Read less

$32.37

Lower Front Felt Seal with Adhesive

★★★★★

(9)

Part #5303937183

The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following tools: #2 Phillips screw driver, #2 square head screw driver, putty knife, and wire bush. If your dryer will not tumble, or makes a squeaking...Read more

Read less

$27.74

M Series Ignition Coil Kit

★★★★★

(25)

Part #5303931775

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, th...Read more

Read less

$158.22

Drain Pump - 120V 60 Hz.

★★★★★

(26)

Part #137221600

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need fo...Read more

Read less

$60.57

Timer Knob

★★★★★

(13)

Part #131873304

This knob accepts a D-shaped shaft.

Manuals & Care Guides for FGX831FS3

Click to download

Install

Installation Instructions

Questions And Answers for FGX831FS3

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:

Susan - For model number FGX831FS3

February 21, 2020

The knob to start the dryer turns but no longer will pull out to start the machine. Should i just replace the knob or is it something more serious?

Hello Susan, Thank you for your question. There is a electric piece that typically goes behind knobs on appliances. Usually, you'll find it is called a "timer". In this case, it's no different. The dryer timer has a shaft that the knob turns when connected to it. If it will no longer pull out, we would recommend taking a look at the timer for your model FGX831FS3, which would be under part number PS462363. We hope this helps you.

Dryer Timer

2 people found this instruction helpful.

Was this helpful?

Joe - For model number FGX831FS3

April 18, 2024

About midway through the washing machine's spin cycle it starts screeching extremely loud. When I turn it off, it continues until the drum stops. I've checked the motor and idler pulley and they appear to be fine. The noise appears to be coming from near the bottom of the drum shaft. What are your suggestions and what parts maybe needed? Thank you for your help.

Hi Joe, thank you for contacting us. You may want to take a look at your spin bearing, part number PS446536, to see if it needs to be replaced. Glad to be of help!

$85.75

Spin Bearing

Was this helpful?

Elmer - For model number FGX831FS3

February 9, 2020

How do i get the front panel off i took the two screws on the bottom off but that is as far as i got.We have a squeak when it is in the wash mode.

Hello and thank you for writing. Unplug the washer from the wall outlet. cate the gap between the front panel and the underside of the top panel that contains the door to the washer. Insert a putty knife or another flat, rigid tool through the gap and push the clips backward to detach them from the front panel. Tip the front panel forward away from the washer. We hope this helps. Please contact us anytime if you require further assistance.

Was this helpful?

Common Symptoms of the FGX831FS3

How this model fails, and the parts that fix it.