FGX831FS1 Frigidaire Washer Dryer Combo - Overview

Diagrams for FGX831FS1

See every part. Know exactly what you need.

Parts for the FGX831FS1

$43.77

Rear Drum Bearing Kit

★★★★★

(114)

Part #5303281153

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if it is making a lot of noise, it could be an issue with this part. This is a ball-and-socket style bearing. You will need to replace this if t...Read more

Read less

$10.93

Drum Support Bearing

★★★★★

(21)

Part #131825900

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although rep...Read more

Read less

$41.75

Drum Glide - White

★★★★★

(17)

Part #137513300

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each ...Read more

Read less

$24.41

Drive V-Belt

★★★★★

(31)

Part #134511600

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; ch...Read more

Read less

$62.37

Door Catch

★★★★★

(31)

Part #131658800

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this instal...Read more

Read less

$54.95

Dryer Lint Screen

★★★★★

(28)

Part #5304516871

This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.

$12.05

Multi-Rib Drum Belt

★★★★★

(14)

Part #137292700

The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Over time this part will naturally dry out. If your drum belt begins to crack or break, the dryer will not be able to continue to turn. If your...Read more

Read less

$32.37

Lower Front Felt Seal with Adhesive

★★★★★

(9)

Part #5303937183

The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following tools: #2 Phillips screw driver, #2 square head screw driver, putty knife, and wire bush. If your dryer will not tumble, or makes a squeaking...Read more

Read less

$27.74

M Series Ignition Coil Kit

★★★★★

(25)

Part #5303931775

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, th...Read more

Read less

$158.22

Drain Pump - 120V 60 Hz.

★★★★★

(26)

Part #137221600

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need fo...Read more

Read less

$60.57

Timer Knob

★★★★★

(13)

Part #131873304

This knob accepts a D-shaped shaft.

$22.97

Dryer Drum Bearing Bracket

★★★★★

(2)

Part #131724301

This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing

Manuals & Care Guides for FGX831FS1

Click to download

Install

Installation Instructions

Questions And Answers for FGX831FS1

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:

Pauline - For model number FGX831FS1

December 17, 2019

Washer overflowing during fill

Hello Pauline and thanks for writing. It certainly sounds like a faulty water level switch PS1146954 check for signs of damage and replace it if needed. We hope this helps. Please contact us anytime.

$88.35

Water Level Switch

Was this helpful?

Peter - For model number FGX831FS1

August 26, 2023

How do I remove the igniter? I've bought a replacement part but can't figure out how to remove the old one.

Hi Peter, thank you for reaching out. To reach components inside the dryer cabinet, you may use a screwdriver to un-thread the screws securing the lower access panel. Detach the panel and set it aside. Insert a putty knife above the front access panel to release the spring clips to detach the panel. Remove the lint screen and use a nut driver to un-thread the screws to release the air duct. Un-thread the four screws securing the heater shield. Now detach the shield to access the heating elements. Now you have access to the igniter. To reinstall follow the instructions backwards. We hope this helps, good luck with this repair!

Was this helpful?

Common Symptoms of the FGX831FS1

How this model fails, and the parts that fix it.