This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If...
$19.77
In Stock
Order within the next 11 hrs and your part ships today!
The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut o...
$50.41
In Stock
Order within the next 11 hrs and your part ships today!
The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing...
$10.92
In Stock
Order within the next 11 hrs and your part ships today!
The surface burner head is used for ranges and ovens, and is located on the cooktop, where the flames go up. The surface burner spreads the gas through holes to create an even flame throughout the ent...
$27.10
In Stock
Order within the next 11 hrs and your part ships today!
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
$12.25
In Stock
Order within the next 11 hrs and your part ships today!
This OEM broiler pan and grate insert are cooking accessories used in your oven to broil food. The pan catches drippings and prevents them from falling into the appliance, while the grate insert ensur...
$68.37
In Stock
Order within the next 11 hrs and your part ships today!
The door lock switch, or simply door switch, is used in ranges and ovens. The switch activates signals to the oven control board about the state of the door lock. If the light in the oven is not turni...
$42.86
In Stock
Order within the next 11 hrs and your part ships today!
The oven light socket allows you to screw in a light bulb so that you can see the inside of your oven. The light socket is located in the back of your oven, so you will need to remove the back panel t...
$46.67
In Stock
Order within the next 11 hrs and your part ships today!
This flat glow bar igniter is designed for gas ovens. The function of the part is to ignite the gas to light the oven burner. If your gas igniter does not glow, or if it glows but will not light, you ...
This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount...
$94.49
In Stock
Order within the next 11 hrs and your part ships today!
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven
... Read moreand attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven,
... Read moreand the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
The repair was nothing, but the diagnosis was a bit tricky. After carefully looking at the burner head, (cast aluminum) I pretty much figured out that the 4 small cast aluminum bumps that keep the burner cap positioned up in the air the correct amount to allow gas to flow under the cap, were worn down, preventing the gas from exiting pro
... Read moreperly by the igniter. My guess was correct. The new burner head solved all my problems. I love Parts Select for the ease of finding the correct parts and how fast they ship their orders. Great company, great service. Keep up the good work