The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is mad...Read moree of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.
Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When makin...Read moreg this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.
This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and upper dish rack, then disassemble the mount and spray arm before installing the new one.
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the basket in the dishwasher is worn out or the basket is broken, replacing it can be a solution. No tools for this replacement are required, as it i...Read mores an easy process. If you need further guidance refer to the instructions provided by the manufacturer. For safety precautions make sure to unplug the dishwasher and wear gloves.
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step gu...Read moreide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely of plastic, and are white in color. The purpose of these parts is to allow your dishrack to roll easily on the support rails. This kit is so...Read moreld individually and contains only one wheel and one axle. Please order the required quantity for your repair. If your dishrack is having trouble rolling in and out you may need replace your rollers and axles.
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and leave the door closed for several hours to properly seat the new door seal.
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, dependin...Read moreg on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.
This fold-down fence with clips is designed to help secure dishes in place during wash cycles in compatible Frigidaire dishwashers. Installed on the rack, it provides added support for smaller or lightweight items that may shift or tip over during cleaning. If dishes are no longer staying upright or are falling over, the fence may be worn...Read more or damaged and should be replaced. This part is sold individually and is sourced directly from the original manufacturer. Please verify compatibility with your specific model before purchase.
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete it you only need a flat blade screwdriver. Use the screwdriver to pry the locking tab open on the cap, located at the front of your upper dishrack. Pull off the end cap and lock the new one into place.
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is ...Read moremade of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.
This dishwasher heating element is a genuine replacement component designed to maintain optimal water temperature during the wash cycle and assist in drying dishes at the end of the cycle. Positioned at the bottom of the dishwasher tub, it ensures efficient cleaning and drying performance. Compatible with a wide range of models from Frigi...Read moredaire, Kenmore, Crosley, Electrolux, and other related brands, this element replaces older versions and restores proper function when symptoms such as poor cleaning, inadequate drying, or water leaks occur. Installation requires disconnecting power to the appliance to ensure safety. Sold individually.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Hope - For model number FGIP2468UF0A
March 31, 2023
I found the lower arm for dishwasher but need the blue orbital sprayer also
Hello Hope, thank you for your query. The orbital sprayer you are looking for is part number PS12717891. Good luck with your repair!
Hello Kevin, thank you for reaching out. The dispenser cap for your model is part number PS421128. If you need help placing an order, customer service is open 7 days a week!
My apologies for the resubmit. I wasn't sure if I included the model number.
I am look for a rinse dispenser cap for a FGIP2468UF0A dishwasher.
Hello Kevin, thank you for reaching out. The dispenser cap for your model is part number PS421128. If you need help placing an order, customer service is open 7 days a week!
Hi Lori, thank you for contacting us. The lower spray arm for your model is part number PS12717896. If you need help placing an order, customer service is open 7 days a week!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The spray arm would fall off during the washing cycle.
827 of 844 peoplefound this instruction helpful.
Roy from Worcester, MA
Really Easy
Less than 15 mins
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having th
... Read moree problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
Read less
Was this helpful?
Thank you for voting!
Lower Rack Roller Missing
379 of 395 peoplefound this instruction helpful.
Sandra from Mount Vernon, WA
Really Easy
Less than 15 mins
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.
Was this helpful?
Thank you for voting!
dishwasher was leaking water
177 of 213 peoplefound this instruction helpful.
Charles from Milton, FL
Really Easy
Less than 15 mins
Screw drivers
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
My Orders
