FGC30S8HBA Frigidaire Cooktop - Overview

Diagrams for FGC30S8HBA

See every part. Know exactly what you need.

Parts for the FGC30S8HBA

$52.96

Burner Cap - LF, LR, RR

★★★★★

(1)

Part #316213500

This burner cap is a replacement cooking surface component designed to distribute heat evenly across the burner. It is commonly replaced when chipped, warped, or damaged by heat exposure.

$59.17

MODULE

★★★★★

(2)

Part #5304505695

$42.61

Burner Pan Gasket

Part #318053901

Liquid collecting beneath a burner pan may mean the surrounding gasket is damaged or out of place. The seal sits between the cooktop and drip pan to block spills from leaking through the joint. First check that the pan is seated correctly and that food buildup is not holding it above the surface. Match the replacement to the complete mode...Read more

Read less

$54.10

Burner Igniter

★★★★★

(1)

Part #318148700

Also known as spark electrode. This part helps your burner ignite and produce flame.

$108.21

Burner Pan - Medium

Part #318168114

Small Burner Cap

Part #316206600

Sold individually.

Burner Pan - Large - Right Front

Part #318168124

Igniter Switch

Part #316032002

When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.

Burner Pan - Small - Right Rear

Part #318168104

This has a small center hole.

Bushing

Part #318146301

Burner Grate

Part #318221711

Sold Individually.

$205.43

Gas Pressure Regulator

Part #5308007974

***No Conversion Kit Required - Adjust On Appliance*** This valve automatically cuts off the flow of a liquid or gas when it reaches a certain pressure.

Manuals & Care Guides for FGC30S8HBA

Click to download

Install

Installation Instructions

Product Specifications Sheet

Common Symptoms of the FGC30S8HBA

How this model fails, and the parts that fix it.

Will Not Start

Fixed by
these parts

Show All

Gas igniter glows, but will not light

Fixed by
these parts

Show All

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

gas ignitor continued to run after turned on or off

10 of 13 people found this instruction helpful.

Duff from Buena Vista, CO
Easy
30 - 60 mins
Screw drivers

Removed all of the grates, control knobs and gas diffusers. Unscrew the drip pans, two on each pan, which attach the pans to the gas supply. Raised the drip pans from the top and unplugged the ignitors from all pans. Remove the top and the rubber deflector over the ignitor switch. The ignitor switch snaps off and on. One of the seals unde ... Read more

Read less

Was this helpful?

Top burners were not lighting without a match

3 of 4 people found this instruction helpful.

Earl from ALLIANCE, OH
Easy
15 - 30 mins
Nutdriver, Pliers

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

Was this helpful?

burner ingnighter would not lite burner

30 of 86 people found this instruction helpful.

Wayne from Palestine, IL
A Bit Difficult
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy ju ... Read more

Read less

Was this helpful?