FGC30S4HCA Frigidaire Cooktop - Overview
Sections of the FGC30S4HCA
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Burner Cap - LF, LR, RR
PartSelect #: PS439750
Manufacturer #: 316213500
This burner cap is a replacement cooking surface component designed to distribute heat evenly across the burner. It is commonly replaced when chipped, warped, or damaged by heat exposure.
$52.96
In Stock
Burner Igniter
PartSelect #: PS443849
Manufacturer #: 318148700
Also known as spark electrode. This part helps your burner ignite and produce flame.
$54.10
In Stock
Small Burner Cap
PartSelect #: PS439723
Manufacturer #: 316206600
Sold individually.
No Longer Available
Igniter Switch
PartSelect #: PS437310
Manufacturer #: 316032002
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
No Longer Available
Gas Pressure Regulator
PartSelect #: PS473609
Manufacturer #: 5308007974
***No Conversion Kit Required - Adjust On Appliance***
This valve automatically cuts off the flow of a liquid or gas when it reaches a certain pressure.
$195.28
Special Order
Square Burner Pan - Black - Kit of 4
PartSelect #: PS2582152
Manufacturer #: 318536711
No Longer Available
Burner Grate Kit - Black - Kit of 4
PartSelect #: PS2581964
Manufacturer #: 318221618
No Longer Available
Manuals & Care Guides for FGC30S4HCA
Click to downloadInstall
Installation Instructions
(0.46MB)
Specs
Product Specifications Sheet
(0.04MB)
Wiring
Wiring Diagram
(0.57MB)
Common Symptoms of the FGC30S4HCA
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gas ignitor continued to run after turned on or off
Removed all of the grates, control knobs and gas diffusers. Unscrew the drip pans, two on each pan, which attach the pans to the gas supply. Raised the drip pans from the top and unplugged the ignitors from all pans. Remove the top and the rubber deflector over the ignitor switch. The ignitor switch snaps off and on. One of the seals unde
... Read more
r the drip pan was broken and needed replaced. I would recommend ordering these also. Turned out this was a good time to give everything a goo cleaning then replace as removed.
Read less
Parts Used:
-
Duff from Buena Vista, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top burners were not lighting without a match
Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly
Parts Used:
-
Earl from ALLIANCE, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner ingnighter would not lite burner
Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy ju
... Read more
st the spark module for the burner.
Read less
Parts Used:
-
Wayne from Palestine, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
30 of 86 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!