All Installation Instructions for Frigidaire Refrigerator FFSC2315LS0

I broke the lever that you npush to get water.

At first glance I didn't see the screws that would permit me to get to the actuator but I lifted the small tray at the bottom and there were two screws. Everything went easily.

Parts Used:

Water Dispenser Actuator

Darryl from Sciotoville, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Switch would not allow door to close.

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Parts Used:

Light Switch

Charles from Front Royal, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

some parts in the ice container had rusted

pulled out the old assy and replace with the new one.

Parts Used:

Ice Bucket and Auger Assembly

John from Santa Monica, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Oven light bulb went dark; it needed replacing

Twisted replacement bulb into place easily. Let there be light!

Parts Used:

Light Bulb

Lise from CEDAR GROVE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

10 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker quit working & was over flowing

We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....

Parts Used:

Rear-Mount Ice Maker Assembly

kenneth from lincoln, NE
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Frost build up on evaporator

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

Parts Used:

Defrost Thermostat Kit

B J from Dillingham, AK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

12 of 24 people found this instruction helpful.

Was this instruction helpful to you?

I took the shelf out to wash it and it broke in a million pieces

I ordered a new shelf and I put in, less than minute

Parts Used:

Crisper Glass Insert

Beverly from PHILADELPHIA, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator Light bulb went out

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Parts Used:

Light Bulb

ANGELA from MEBANE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

chrisper drawer jammed found supports were broken

Looked at video on how to remove and reinstall support and followed the instruct ions

Parts Used:

Crisper Cover Support - Front

Crisper Support - Rear

ROMAN from COLTON, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The top crisper drawer frame was cracked, it secures the glass top also.

Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.

Parts Used:

Upper Crisper Drawer Frame

Chuck from PHILADELPHIA, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Ice tray wouldent fill.

It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

Parts Used:

Rear-Mount Ice Maker Assembly

Eric from Greensburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

When washing the shelf insert glass piece, it broke into a million pieces.

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Parts Used:

Crisper Glass Insert

Gayle from Hot Springs Village, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Water dripped from water outlet on door

Replaced the Triple Water Valve

Parts Used:

Refrigerator Water Inlet Valve

Douglas from Denver, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Support stude for both vegetable crispers broken off

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Parts Used:

Crisper Cover Support - Front

RANDY from NORTH CHARLESTON, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Replace ice maker which was splashing water

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

Parts Used: