FFHT1513LS0 Frigidaire Refrigerator - Instructions

This was so easy it took longer to open the door than it did to install the rack. WOW. Nice to see something fits without messing with it. Thanks.

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

first i order a defrost termostate i replace it but wasnt the problem then i
unpluged the evaporator fan motor and test it and was not working order
a new one and working like new.

One of our employees needed to bring in a screw driver for square holes which he picked up at lunch. It took less than 5 minutes to replace the old one. He removed 2 screws, put the new handle on and screwed it in.

replaced it

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

My unit was not defrosting. Defrost heater was not functioning. Defrost heater tested good with a meter. Thermostat (cold) tested bad with a meter. Defrost timer was working properly. I replaced the thermostat but I had to buy red crimp connectors because the blue ones that came with the thermostat are designed for wire bigger than 18 AWG wire. The thermostat leads as well as the wire in my unit were 18 AWG. The crimp was not tight enough for my liking with the blue butt connectors. I also purchased smaller heat shrink tubing. After replacement, the defrost heater started working. I could see it glowing. Unfortunately immediately after getting the heater working the contacts in the defrost timer arced and stuck together thus preventing the timer from exiting defrost mode. The heater went off at this point indicating that the thermostat was now working. I then purchased and replaced the defrost timer and now the fridge is functioning properly. I noticed both replacement parts, even though I looked up my fridge model, were different part numbers than the originals. I'm guessing the new parts are improved? I also noticed the timer was an 8/30 rather than a 10/30 like the original. The fridge is working better than when it was new so evidently defrosting every 8 as opposed to every 10 hours is better for my unit.

Long story short:

Buy the correct crimp/butt connectors before beginning replacement of the thermostat and proactively replace the defrost timer since it is rather inexpensive.

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.

it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

I went online to a you-tube video to assess the problem and watch the repair. Ordered the part on sunday before christmas and had it christmas eve! Easy 10 minute repair. Four screws held the cover on. Two screws held the timer. Unplugged the old timer an replaced. Put all the screws back and . . . . Done! Easiest repair I've ever done. Parts select did a great job, good price, very fast service! One happy customer!

2 screws out ,bracket out,bracket in,2 screws in DONE

Glued and taped old door rack until new part arrived. Perfect fit.

I got the model number and because you offered diagrams I was able to order the correct replacement. The piece slid right in and I thought it was miraculous. It was so easy.

Very easy to do, as per the video instructions.