This is a 120 volt defrost timer manufactured for refrigerators. The defrost timer manages the automatic defrost systemin the unit. It acts like a clock by switching between activating the cooling cycle and the defrost heater to maintain the set thermostat temperature, preventing the unit from being too warm or cold. The defrost timer may...Read more need to be replaced if the fridge will not maintain its temperature or has frost buildup. Depending on the model, it could be located on the rear panel or ceiling of the fresh food compartment. Be sure to disconnect power to the refrigerator before replacing this part.
This part helps maintain a constant temperature within the appliance. The temperature control thermostat regulates the temperature inside the refrigerator. It turns on and shuts off the compressor as needed to maintain the set temperature.
This evaporator fan motor is 115V. If you notice that your freezer is noisy or is too warm, you may need to replace the evaporator fan motor. This package comes with the evaporator fan motor itself, as well as a wire harness. The evaporator fan motor is in the back of the freezer, so you will need to remove your freezer shelves and the ba...Read moreck panel before you can access it. The function of the evaporator fan motor is to circulate air over the coils. The coils convert the heat into cool air, which is then circulated. Be sure to remove the power source from the freezer before you begin this repair.
This metal shoulder screw secures a refrigerator or freezer door handle to the outer door panel. It is a number 10 AB handle mounting screw and is sold individually. A missing screw, damaged threads, or a worn screw head may leave the handle loose or prevent it from attaching securely. Check the handle and mounting point for damage before...Read more replacing the screw, since either can also cause movement. Confirm the correct fastening location in the appliance parts diagram before installation. This is an OEM part sourced directly from the manufacturer.
This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be...Read more one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.
Secure hinge attachment helps keep a refrigerator or freezer door supported during opening and closing. This hinge mounting screw fastens the hinge bracket to the cabinet framework and features a hex washer head for tightening with a nut driver or socket. Its thread size is 1/4-20, with a length of 5/8 inch. Missing hardware, stripped thr...Read moreeads, or a damaged head may leave the hinge loose. Replacing a damaged screw helps restore a firm connection and stable door support when the cabinet threads remain intact. This is an OEM part sourced directly from the manufacturer.
A compressor that clicks or hums without starting may be associated with a failing run capacitor. The capacitor stores and releases electrical energy to support compressor startup and operation. If the compressor does not engage, the appliance may become too warm. This is an OEM part. Disconnect power before working on the appliance.
This hinge bearing supports smooth door movement while maintaining proper alignment. Reduced friction helps prevent wear and ensures easy opening and closing. Replacing a worn bearing restores smooth and stable door operation.
This filter drier removes moisture and traps small particles in the refrigerator sealed refrigerant circuit. It helps keep dirt, metal fragments, and moisture from moving through the cooling system. The component measures approximately 11 inches long. A blocked or faulty filter drier may restrict refrigerant flow and contribute to poor co...Read moreoling even while the compressor runs. These symptoms can also come from other sealed system faults, so confirm the failed component before replacement. Match the filter and tubing connections to the appliance service requirements before selecting the replacement. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer would run then thaw then freeze. tap on the control knob, it would start running again
48 of 59 peoplefound this instruction helpful.
WILLIAM from URBANA, OH
Easy
15 - 30 mins
Screw drivers
Easy fix. I unplugged the freezer, unload items in freezer. took out shelves and baskets, Pulled off the control knob then removed all screws. removed inside panel, replaced part exactly as I took out old part. Put the panel back on, put everything back in place. Plugged freezer back in and turned the knob to 3. Let freezer run for a day
... Read more to see if I ordered the correct part. Problem is fixed. Thank you, PartSelect for making it so easy to find, order the correct part and for all the customers input to make the repair easy.
Read less
Was this helpful?
Thank you for voting!
Temp alarm sounding and food on top shelves partially thawed
43 of 52 peoplefound this instruction helpful.
Wayne from Forest Hill, MD
Easy
Less than 15 mins
Screw drivers
After silencing the alarm, it seemed to be running as normal without any unusual noises, but food was starting to thaw from the top shelf on down and condensation was dripping from the roof. We were able to place most of the food in 2 large ice chests and then the rest in the freezer compartments of 2 fridges we have in the house. I the
... Read moren turned down the temp dial to the coldest setting and let it run for an hour or so; no change.
After researching on the internet, it sounded like our symptoms could be pointing to a defrost timer issue. I pulled the freezer away from the wall, located the timer and used a large screwdriver to slowly advance it. While doing this, at one point I could hear the compressor kick in. I pushed the quick freeze button and let it run for a while. When I checked it in a few hours, the alarm light had gone out and water that I had placed inside was frozen. We took a chance and put the food we placed in the ice chests back in the freezer. Everything was fine several hours later.
I ordered a new defrost timer, it arrived in a couple of days, and replaced the old one with it in a matter of minutes by disconnecting the wire harness from the old timer, removing the 2 screws holding it onto the bracket, screwing the new timer to the bracket, reconnecting the wires harness, and done. It's been a week or so and no problems.
Read less
Was this helpful?
Thank you for voting!
freezer compressor ran continuously and freezer getting colder and colder.
34 of 42 peoplefound this instruction helpful.
john from hurst, TX
Easy
15 - 30 mins
Screw drivers
Repair was quick and easy. I removed the frozen food in the bottom so the back panel could be removed. The temperature comtrol is attached to the back of that panel. It has a metal wire with a capillary tube on the end to sense the temperature. I just installed it exactly like the old one came out. Be sure and don't get the wire
... Read mores mixed up. Sometimes it helps to make notes. This was also a good time to clean the bottom out and make sure the drain hole was clear.
It took two days for the temperature to stabilize. I was anxious for a couple days that there was something else wrong. However, it smoothed out and the temperature control (thermostat) is now working properly.